6ES5 955-7NC12

The Siemens 6ES5 955-7NC12 is an S5 955 power supply for the SIMATIC S5-155H central rack, designated ZG 155H in Siemens documentation. It takes a 24 V DC input and supplies 5 V DC at 14 A to the central rack. Siemens lists this order number as a spare part.

The basic S5-155H configuration in the SIMATIC S5 family uses two central racks in an active/standby arrangement. Each rack has its own power supply and CPU 948R. If one rack loses power, the condition of the other side determines whether the process keeps running.

24 V input and 5 V rack supply

The 14 A rating applies to the 5 V output. Size the upstream 24 V DC power supply for the module’s input current and any other loads on that feed. Where cabinet loads share the feed, check whether a brief interruption or a voltage drop at the module input coincides with the fault.

Record a loss of the 24 V input separately from a loss of the 5 V rack supply. The first points upstream towards the cabinet feed. With the second, the supply module, the rack and its connected loads are all part of the investigation.

Central racks, expansion units and the link between sides

Start by identifying the affected S5 rack. A central-rack power fault and a loss of power in an S5 expansion unit affect different parts of the system. The Siemens system manual covers central and expansion units separately.

The central racks exchange data over a parallel link built from S5 interface modules and the associated interconnecting cables. If both racks remain powered but the link drops out, check the CPU diagnostic records and the inter-rack connection.

Why the full 955 order number matters

The 6ES5 955-7NC11 is also listed for the 155H with a 24 V DC input and a 5 V DC, 14 A output. Before selecting a replacement, check the complete order number, rack type and hardware revision alongside the electrical ratings.

The 955 family also includes 18 A DC-input versions such as the 6ES5 955-3NC42 and AC-input units such as the 6ES5 955-3LF12. Use the input type, output rating and rack designation together when checking a spare.

Narrowing down a power-related fault

If the fault affects only certain digital inputs or digital outputs, establish whether those points share a field supply. If only analog channels are affected, check the wiring and supply for that channel group separately.

When the symptom is a loss of data exchange, compare the diagnostic records from the affected S5 communications module and the CPU over the same period. If an entire side goes down, correlate the active/standby state with the cabinet power records and the symptoms at that rack.

Editor’s note

Photograph both nameplates. Record the 7NC12 suffix and any visible hardware revision on the supply. A photo of the rack nameplate helps identify the installed combination when several 955 units look alike.

Record which side went down. Note the A/B designation and which rack was active at the time. If the system switched sides, record the status before and after the changeover.

Capture the timing. A drop-out at power-up, a fault after warm-up and a fault when another cabinet load starts are different clues. Compare the cabinet event log with the CPU timestamps to establish the sequence.

Define the scope of the work. If other modules will be disturbed, record the CPU configuration and any installed S5 memory card details. Use the site’s S5-155H maintenance and return-to-service procedure for the job.

Ask what the test covered. When comparing used PLC power supplies, ask whether the unit you’re buying was checked under load and whether the result was recorded. If a measurement is available, ask what load was applied during the test.

OtomasyonAVM references and PDF archive

See our Siemens S5 PLC overview for the wider platform and the SIMATIC S5 power supply index to compare order numbers.

Our OtomasyonAVM S5 PDF page includes the S5-115H and S5-100U manuals. The 155H system manual and the data sheet for this order number are under External references below.

Related topics

For cabinet power continuity, see uninterruptible power supplies. For rack and CPU identification, browse S5 racks and the S5-155H CPU 948R 6ES5 948-3UR23 page.

Site navigation

Siemens Automation › Siemens S5 PLC › SIMATIC S5 › S5 power supplies

External references

Siemens 6ES5955-7NC12 data sheet (PDF)

Siemens SIMATIC S5-155H system manual, volume 1 (PDF)