6ES5 955-3LF11

The Siemens 6ES5 955-3LF11 is a fan-cooled S5 955 power supply for SIMATIC S5-135U and S5-150U central racks. Siemens specifies a 110 or 220 V AC, 50 Hz input and a 5.1 V DC, 40 A main output for the rack’s internal 5 V rail. The unit also has a 24 V DC auxiliary output and two axial fans.

In a SIMATIC S5 installation, the supply powers the processor and other modules in the central rack. When identifying a spare, record both the power supply order number and the nameplate on the S5-135U central rack or S5-150U central unit.

AC input and voltage selector

The S5-150U manual specifies 110 or 220 V AC ±15% and identifies a voltage selector. The power supply index also lists this model as 115/240 V AC. Check the installed unit’s nameplate and selector position when confirming which feed it requires.

If the rack restarts or shuts down unexpectedly, check the event record for a brief mains interruption or a voltage drop at the cabinet input. The Siemens manual gives a typical mains-failure hold-up time of 15 ms.

Main rail and auxiliary outputs

The 40 A rating applies to the 5.1 V main output feeding the S5 rack. The 24 V DC auxiliary output is rated at 2.8 A. With the optional 15 V submodule installed, the combined load on the 24 V and 15 V outputs is limited to 2.8 A.

If a fault affects only a group of digital inputs or digital outputs, trace that group’s power supply in the cabinet drawings. If the symptom is confined to one expansion unit, include its interface module and inter-rack cable in the investigation.

Fan monitoring and cabinet heat

Two axial fans cool the unit. Siemens documents LED or relay indication for a stopped fan. The jumper configuration can also make a fan fault shut down the outputs. The cabinet ventilation section lists a maximum heat dissipation of 140 W for the 3LF11. If shutdowns start after warm-up, review the fan status and cabinet airflow together.

Comparing the 3LF11 with other 955 supplies

Siemens assigns the fourth 24 V output, rated at 0.4 A, specifically to the 6ES5 955-3LF12. That auxiliary-output difference matters when comparing units with the same main output rating.

The 6ES5 955-3NF11 takes a 24 V DC input, while the 6ES5 955-3LC13 has an 18 A main output. When comparing another 40 A version such as the 6ES5 955-3LF41, check the complete order number, rack designation and auxiliary outputs.

Editor’s note

Photograph the supply and rack nameplates. Record the 3LF11 suffix and the selector position in the service record. Those details make it easier to match the removed unit to the cabinet documentation.

Trace the auxiliary circuits before ordering. Mark the loads on the 24 V output and any fitted 15 V submodule on the drawings. Check that the replacement covers those circuits as well as the main rail.

Capture the first alarm. A fan warning, loss of power and a CPU stop can follow one another quickly. The order in which they occurred helps identify where to start.

Note when the symptom returns. Log a fault on a cold start separately from one that appears after the cabinet warms up. Compare the timestamps with other cabinet events if records are available.

Ask what the bench test covered. When comparing used PLC power supplies, ask what load was applied to the main and auxiliary outputs and whether both fans were operating during the test.

OtomasyonAVM references and PDF archive

Browse our Siemens S5 PLC section for central rack references and the OtomasyonAVM S5 PDF page for documentation on other S5 series. The S5-150U manual with the 3LF11 technical data is linked under External references below.

Related topics

For cabinet power continuity during supply interruptions, see uninterruptible power supplies.

Site navigation

Siemens Automation › Siemens S5 PLC › S5 power supplies

External references

Siemens SIMATIC S5-150U system manual (PDF, German) · The technical data section covers the 3LF11 and 3LF12 outputs. The cabinet ventilation section covers fan monitoring and heat dissipation.