6ES5 955-3NF11

Siemens 6ES5 955-3NF11 SIMATIC S5 power supply, 24 V DC input, 5.1 V DC / 40 A output

The Siemens 6ES5 955-3NF11 is a fan-cooled 955-series rack power supply for SIMATIC S5. It runs from 24 V DC and delivers 5.1 V DC at 40 A to the rack backplane. Siemens specifies this order number for the S5-135U 6ES5 135-3UA51 and S5-155U 6ES5 155-3UA21 central controllers. The S5-150U spare-parts list also identifies it as the 24 V DC supply option.

The unit powers the CPU and module electronics in the S5 rack and incorporates two axial fans and a 24 V auxiliary output. The 6ES5 955-3LF12 also supplies 40 A on its main rail but takes 120/230 V AC. The 6ES5 955-3NC42 takes 24 V DC and has an 18 A main output. Check the input type and the main output rating together when identifying a replacement.

Input current and auxiliary output ratings

The S5-155U manual specifies a 24 V DC input (+25% / −17%). At 24 V DC and rated load, the supply draws 17.5 A. Siemens lists a 300 A peak inrush current. The 3NF41 and 3NF42 share the nominal 24 V DC input and 40 A output rating, so use the manual for the exact suffix when checking input tolerance and startup behaviour.

Allow 2.8 A in total across the auxiliary outputs. This budget covers the backplane 24 V rail, the 24 V / 0.4 A front-panel output and the optional 15 V / 2 A output. A CP 535 or CP 143 installation requires the 15 V add-on. The S5-150U spare-parts list shows the 6ES5 956-0AA11, while the EG 185U documentation lists the 6ES5 956-0AA12.

Checking the rack and CPU configuration

Siemens also lists the 3NF11 as a spare for the EG 185U. Parts catalogues also list the EG 183U. Check the full order number and power configuration on the expansion rack label. The 6ES5 185-3UA11 and 6ES5 183-3UA12, for example, are AC-fed configurations within the 185U and 183U families. In a system with rack interface modules, trace the affected unit back to the central or expansion rack before selecting a replacement.

An S5-155U installation can use the CPU 946/947 assembly. The S5-150U parts list includes processors such as the CPU 924 and CPU 927. Record the CPU identification alongside the full rack and power supply order numbers so a later service call can match the actual hardware.

Fan monitoring, undervoltage and BASP

The supply monitors airflow through both 24 V DC axial fans. With the F-R jumper closed, a fan fault shuts off the supply outputs. With the jumper open, the installation relies on its external shutdown circuit. If the cabinet uses the fault relay, trace the circuit through the S5 wiring and connectors shown in the rack diagram.

Under the conditions set out in the manual, a low voltage at the monitor input or on the main rail can assert BASP and disable S5 digital outputs. If several outputs drop together, include the rack supply and voltage-monitoring circuit in the diagnosis.

Editor’s note

Read the suffix on the label. A 955 marking and a 24 V input still leave several possibilities. The 6ES5 955-7NC11 and 6ES5 955-7NC12, for instance, are listed as 14 A supplies for the S5-155H. Keep a photo of the rack label with the supply label when sourcing a spare.

Capture the fault before resetting. Record whether Fan Fault or Batt Low is lit and whether the interruption occurs at startup or while the machine is running. That timing helps narrow down where to look first.

Document the jumper settings before removal. With the unit isolated, photograph F-R and the other fitted jumpers. The S5-155U manual documents battery fault signalling through the RR-LL relay option from hardware version 7 of the 3NF11.

Check that the STEP 5 backup is current. Confirm how S5 program memory is backed up before removing the supply. A power interruption while the backup battery is in alarm can erase the program held in RAM.

Ask for test results under load. When comparing used PLC power supplies, request a readable label, a loaded measurement of the 5.1 V rail, the state of the auxiliary outputs and confirmation that both fans operate.

OtomasyonAVM resources and PDFs

About Siemens SIMATIC S5 PLCs · SIMATIC S5 racks

OtomasyonAVM SIMATIC S5 PDF archive — manuals published on the site for the S5 family.

Related topics

6ES5 955-3NF41 power supply · 6ES5 955-3NF42 power supply · 6ES5 955-3LF12 AC-input power supply

Browse this family

Siemens S5 PLCs → SIMATIC S5 → S5 power supplies

External references

Siemens S5-155U manual — 3NF11 technical data, section 6.2

Siemens S5-135U manual — controller and power supply assignments, table 1

Siemens S5-150U manual — 24 V DC power supply and spare parts (German)

Siemens U-Periphery manual — EG 185U, table 5.1

6ES5 955-3NF11 parts listing — EG 183U and EG 185U