6ES5 312-5CA22
Siemens 6ES5 312-5CA22 — IM 312-5 Interface Module, 1.5 m Cable
The Siemens 6ES5 312-5CA22 is an IM 312-5 interface module for centralized connection of EU 184U and EU 187U expansion units in SIMATIC S5 systems. It has a permanently attached 1.5 m connecting cable. Within the S5 interface range, it is installed on the expansion-unit side.
The central-side partner is the 6ES5 300-5CA11 IM 300-5C. For EU 184U chassis such as 184-3UA11 and 184-3UA21, the internal 5 V operating supply is transferred through the interface. Treat fan power and electronic-module power separately.
Cable length and connection limits
The S5 connecting cable is fixed to this module; 1.5 m is the length of its own lead. The manual’s centralized arrangement allows a maximum total cable length of 2 m per branch. Include any onward connection in that total.
One IM 300-5 supports up to three expansion units within the manufacturer’s layout conditions. Check the rack arrangement alongside grounding and equipotential bonding between cabinets.
5 V supply and current budget
Siemens ST 50 specifies IM 312 consumption of up to 0.2 A at 5 V and power loss of up to 1 W. The 5 A limit at each IM 300-5CA11 connection applies to the total supplied branch. Keep these figures separate when adding up the installed modules’ demand.
Differences between related codes
The 312-5CA12 is the 0.5 m cable version of this application group; the 5CA22 has a 1.5 m cable. When comparing 312-5CA11 and 312-5CA21, record the complete labels and leads. The final digit alone is insufficient for a replacement decision.
The 312-3AB12 and 312-3AB32 belong to arrangements using an IM 300-3AB11 and an EU 183U with its own power supply. IM 312-3 and IM 312-5 must not share one chain. The 300-5LB11 serves the ER 701 connection group; check suffixes carefully.
Termination and fault checks
No terminator is required at the last IM 312-5. The 760-0AB11 terminator is for IM 312-3. Where an IM 301 provides an additional centralized connection, confirm the 301-5CA12 arrangement in the manual.
The IM 312 has no indicators or controls. During troubleshooting, inspect the partner interface, cable and supply. Check expansion addresses in the PLC program as well; module addresses must not overlap.
Editor’s note
Start with the cable: 5CA22 is the 1.5 m version. Photograph the full lead together with the label. Having both to hand saves a lot of back-and-forth later.
Look closely for damage at the cable entry, hardened insulation and bent connector pins. A clean exterior is only part of the picture; a poor contact can take time to track down.
If several modules disappear together, check their shared supply and connection first. Narrowing the fault before replacing parts saves both time and equipment.
Record chassis numbers, cable routing and addresses before removal. Switch off power and follow the manual for replacement. Keep photographs of the original arrangement; they can be a real help.
For a used module, ask where possible for a working check with a suitable central controller and expansion unit. Include the attached cable in the test so the check covers the complete assembly.
OtomasyonAVM resources and PDFs
+ About Siemens S5 PLCs · S5 interface modules
+ Siemens S5 PDF files — our manual archive. Manufacturer catalogue and system-manual references for this model appear below.
Related topics
+ 300-5CA11 · 312-5CA12 · 312-5CA21 · EU 184U chassis
Browse SIMATIC S5
+ S5 interface modules · S5 racks · S5 cables · SIMATIC S5 · Siemens second-hand equipment
Siemens and external references
+ Siemens ST 50, 1998 — 4/140: 6ES5 312-5CA22 ordering code, cable and technical data
+ Siemens S5-135U/155U system manual — 7-2–7-4: IM 300/312 matching, power and termination
+ Same manual — 7-9, Figure 7-6: total cable length and current limits