6ES5 456-7LB11

Siemens 6ES5 456-7LB11 — 8-Channel AC Digital Output Module

The Siemens 6ES5 456-7LB11 is an 8-channel, 115/230 V AC digital output module for S5-115U/F systems in the SIMATIC S5 family. The manufacturer's data sheet specifies a rated output current of 2 A per channel. This S5 digital output module provides optocoupler-based galvanic isolation, with one output per isolated group.

It transfers output commands from the S5 central controller to AC field loads. When reviewing PLC input/output operation, account for its semiconductor AC outputs; they do not operate as mechanical relay contacts.

Voltage, load current and switching

The S5-115U manual specifies a 115–230 V AC rated load supply, an 89–264 V AC permissible range and a frequency of 47–63 Hz. The ON-state load-current range is 40 mA–2 A, and the maximum switching frequency is 10 Hz. Outputs must not be connected in parallel to increase current capacity.

OFF-state current and load compatibility

The manual gives a typical 3–5 mA residual current with an output command of “0”. For low-current loads, checking the command bit alone is therefore insufficient. Verify the pickup and dropout requirements of the contactor coil; different Siemens contactors need not behave identically on this output.

Applications requiring a relay contact need a suitable output type. The 6ES5 458-7LB11, for example, is a separate relay-output model with different connection and load characteristics.

Fuse protection and red indication

The manufacturer manual specifies a 6.3 A FF fuse for each output group. Preserve both the fuse current rating and its FF characteristic. The red indicator signals a defective fuse. Its rating does not mean that the output can drive a 6.3 A load.

Front connector and installation

The ST 50 technical table specifies a 24-pin front connector for this module; the screw-terminal 6ES5 490-7LB11 has this format. The 6ES5 490-7LB21 is a 46-pin version. Select S5 cables and connectors by checking pin count, the terminal diagram and existing wiring together.

Work on the module and front connector in the S5 rack with both PLC power and field-load supplies disconnected. During PLC debugging, check the command, output and load supply separately. Interpret an unloaded multimeter voltage reading alongside behaviour under load. Review grounding and cable routing when assessing noise immunity.

Comparison with related models

The 6ES5 456-7LA11 is a 16-output, 115/230 V AC, 1 A model. The 6ES5 454-7LB11 provides 8 outputs at 24 V DC and 2 A. Similar channel counts or current ratings do not establish direct interchangeability.

Editor's note

Start with the complete 456-7LB11 label and the load's AC voltage. Similar-looking boards can serve different circuits, and a careful AC/DC check protects otherwise sound equipment.

Do not condemn the board just because a meter shows voltage with the output off. Semiconductor outputs have residual current; interpret the reading with suitable load conditions in mind.

If a fuse has failed, give the cable and connected load a proper check before replacing it. Finding the cause once is better than repeating the same repair.

When checking a used board, test all eight outputs with a suitable AC load. Indicator lights are a useful start; reliable switching of the actual test load tells you much more.

Keep photographs of the old label and front-connector wiring, together with the test result. Stored with the S5 system information, these small records help both you and the next person servicing the machine.

OtomasyonAVM resources and PDFs

+ Start with the OtomasyonAVM S5 PDF archive.

+ Exact-model electrical specifications appear in S5-115U Manual, 15-39; comparison and connector information appear in ST 50, 3/37–3/38.

Related topics

+ 456-7LA11 AC output module · 454-7LB11 DC output module · 458-7LB11 relay output module.

+ 490-7LB11 front connector · What is an optocoupler? · What is a fuse?.

Browse SIMATIC S5

+ S5 digital output modules · SIMATIC S5 central controllers · Siemens S5 main page.

+ Used Siemens automation equipment.

Siemens and external references

+ Siemens S5-115U Manual — EWA 4NEB 811 6130-02b: page 15-39, PDF page 567; 8 outputs, AC ratings, minimum load, residual current, fusing and terminal diagram. English.

+ Siemens ST 50 Catalog — 1998: pages 3/37–3/38; technical comparison and front-connector selection. An externally archived copy of the manufacturer catalog.

+ Siemens 6ES5 456-7LB11 data sheet — November 6, 2020: S5-115U/F, 8 outputs, 115/230 V AC and 2 A description. An externally hosted copy of the German manufacturer document.