6ES5 435-7LB11

Siemens 6ES5 435-7LB11 — 16-Channel 115 V UC Digital Input Module

Siemens 6ES5 435-7LB11 is a 16-channel, 115 V UC (AC/DC) digital input module for S5-115U/H systems in the SIMATIC S5 family. It provides optocoupler-based galvanic isolation, with the inputs arranged in eight groups of two. This grouping is an essential distinction when selecting S5 digital input modules.

The module transfers 115 V on/off signals from field contacts to the PLC. The defined ranges are 0–40 V for signal “0” and 85–135 V for signal “1”. AC operation requires 47–63 Hz. It should not be selected for direct connection of 24 V sensor signals.

Signal levels and input delay

An input voltage above 40 V and below 85 V lies outside the manufacturer’s defined “0” and “1” ranges. Typical input current at signal “1” is 10 mA with 50 Hz AC or 6 mA with DC.

Input delay is 2–13 ms for a 0→1 transition and 10–25 ms for a 1→0 transition. Overall response also depends on the PLC program and scan time. Assess these timing limits before considering the module for short pulse signals.

Paired input groups and connection checks

Trace each pair’s return connection using the manufacturer’s L1/N or L+/M diagram. Bridging group returns without checking the circuit can defeat the intended isolation arrangement. Check grounding, group returns and S5 field cables as separate parts of the installation.

The ST 50 catalog specifies a 24-pin front connector. Review the S5 rack position, existing input addresses and front wiring together. During PLC debugging, compare the channel LED with the corresponding input bit in the program.

Typical field signals

Suitable circuits can supply status signals through relay contacts and contactor auxiliary contacts. A poor connection in a relay socket can also look like an input fault. This module reads signals; driving a coil requires a suitable digital output module.

Differences from nearby order numbers

6ES5 435-7LA11 arranges its 16 inputs in groups of four, while 6ES5 435-7LC11 has eight individually isolated inputs. 6ES5 435-7LB11 combines 16 inputs with groups of two.

6ES5 436-7LA11, 6ES5 436-7LB11 and 6ES5 436-7LC11 belong to the 230 V UC family. 6ES5 434-7LA12 also has different input characteristics. Similar housings do not establish direct interchangeability.

Editor’s note

Take a moment to check the 7LB11 suffix and the actual 115 V field signal before ordering. With S5 hardware, a familiar housing does not guarantee the same voltage or wiring.

If two inputs disappear together, give the card a fair chance before replacing it. The inputs share returns in pairs, so start with that pair’s return wire and terminals.

If an input stays on after its contact opens, investigate leakage current and residual cable voltage. Evaluate the measurement between the input and its own group return.

Photograph the label and connector before removal; those pictures can save time later. Keep a program backup, isolate the supply and verify absence of voltage before changing connections.

When buying a used digital I/O module, do not decide from the LEDs alone. A suitable test setup should demonstrate all 16 channels, every one of the eight groups and the matching program bit changes.

OtomasyonAVM resources and PDFs

Start with the system manual and connection diagrams in S5-115U PDF files. For family background, see about Siemens S5 PLCs.

Related topics

+ 6ES5 435-7LA11 · 6ES5 435-7LC11 · 6ES5 436-7LB11 · PLC debugging

Navigation: SIMATIC S5 | Digital input modules | S5 racks | Used digital I/O | Siemens

External references

+ Siemens S5-115U Manual — 6ES5 435-7LB11, page 15-26

+ Siemens ST 50, 1998 — specifications 3/31 and ordering data 3/32