GD300-19

INVT GD300-19 Goodrive300-19 crane and hoist drive

The INVT Goodrive300-19 (GD300-19) is a crane and hoist VFD designed to control the speed of three-phase induction motors. It supports V/f control and sensorless vector control. Its dedicated hoist functions include motor pre-excitation, torque verification and mechanical brake control.

INVT’s application note gives a three-phase 380–440 V AC input class and a 1.5–500 kW series range. The model table in the English manual linked below covers 1.5–315 kW. INVT lists overload figures of 150% for 60 s, 180% for 10 s and 200% for 1 s. When selecting a crane drive, check the full drive code, rated output current, motor nameplate and duty cycle together.

Hoisting, lowering and the mechanical brake

On an overhead crane, the hoist axis carries the load vertically. The trolley and bridge travel horizontally. On the hoist axis, the motor must take the load before the brake releases. At a stop, the mechanical brake must hold the load again. The GD300-19 manual covers these functions in the P19 hoist group and section 7.17 on brake control. The guides to open-loop and closed-loop control and torque control explain what to look for at low speed.

Preset speeds let the operator call for slow or fast motion. Acceleration and deceleration ramps govern the transitions. Compare the frequency reference, raise and lower directions, limit switches and brake feedback against the machine’s wiring diagram. A qualified team should commission the system and verify the brake under the site’s crane safety procedure.

Where does the braking energy go during lowering?

When the load drives the motor, regenerative energy can flow back to the drive’s DC bus. In resistor-based dynamic braking, a brake chopper switches the energy to a braking resistor, where it is dissipated as heat. The mechanical holding brake keeps the stopped load in place. Check the exact drive code for the built-in or external braking unit, approved resistance and braking duty.

Motor settings, fault history and software

Record the motor’s rated power, rated frequency, voltage, current and speed from the nameplate. Choose the auto-tuning method according to the hoist mechanism and the manufacturer’s procedure. If a fault occurs, record the displayed code and whether it happened during lifting, lowering or stopping. Read the P07 fault records alongside the manual’s fault table. The VFD fault guide and overload guide explain the underlying terms.

See INVT VFD Software for INVT Studio. The manufacturer lists GD300 support. Confirm GD300-19 compatibility with the software version and drive firmware before connecting. For Modbus RTU monitoring via RS-485 with a PLC or HMI, use the register and scaling table in the GD300-19 manual. The INVT Modbus address guide provides general context.

Manual and technical documents

Start with INVT VFD Documents, the relevant OtomasyonAVM document category. The wider archive is under INVT user manuals. The external references below include the English online manual, links to key sections and the Chinese V2.1 PDF.

Editor’s note

If you are sourcing a spare, start with a clear photo of the nameplate. Make sure GD300-19 and the power and voltage suffixes are readable.

If a crane jerks as it takes the load, go over the motor data, brake release timing and brake feedback with the team.

If it trips while lowering, write down the display code and the exact point in the move. The brake chopper and resistor circuit belong in that investigation.

On a used drive, terminal damage, discolouration, fan noise and any stored fault history can tell you a lot. After the bench check, leave on-crane acceptance testing to a qualified team.

Keep the old wiring diagram and parameter record. If someone changed the brake circuit or limit switches, finding that change on paper before commissioning saves time. Crane maintenance and repair

Related topics

What is a VFD? · Choosing a hoist drive · Current limiting

Standard GD300 series · CHV190 hoist drive · GD300L elevator drive · INVT fault codes · INVT application notes

Browse INVT brand home › INVT VFD drives › VFD documents

External references

Goodrive300-19 operation manual (English) · P19 parameters · Brake control · Fault tracking · Modbus register table · Braking hardware

Goodrive300-19 operation manual V2.1 (Chinese PDF) · INVT GD300-19 mine-hoist case study · INVT GD350-19 crane drive manual (separate series, PDF)