Delta ASDA-A2R
Delta ASDA-A2R Servo Drives
Delta ASDA-A2R is an AC servo drive series for compatible ECML linear motors and ECMA rotary servo motors. With a compatible linear scale connected through CN5, the drive can use external scale feedback for full-closed-loop operation. This lets axis control use the actual position of the moving table or measurement axis.
Drive and motor matching
This category covers the ASD-A2R-0121, 0221, 0421, 0721, 1021, 1521, 2023 and 3023 base codes. Before ordering or replacing a drive, check the full drive suffix, supply rating, motor nameplate code and feedback type against the motor and drive selection table.
Delta’s matching table lists the ECML-S2504A2DNS with the ASD-A2R-0421-□ (400 W) and the ECML-S3208A2DNS with the ASD-A2R-0721-□ (750 W). On an ECML axis, also verify the coil and magnet track combination. For rotary applications, confirm the compatible Delta ECMA motor and its motor encoder by the full model code.
CN5, external scale and full-closed-loop control
CN5 provides differential A/B/Z inputs for a 5 V external scale encoder. The linear motor wiring section also documents Hall U/V/W and NTC/PTC motor temperature inputs. Verify the feedback type and wiring diagram for the exact motor model.
For external-scale motion and position control, P1-72 sets linear scale resolution and P1-73 sets the allowed position difference between scale and motor encoder feedback. P1-74 covers loop selection, scale direction and filtering. Check the command’s electronic gearing and the scale’s measurement conversion separately.
User manual and catalog
ASDA-A2R user manual (EN) · Motor matching, CN5 wiring, full-closed-loop parameters and alarm diagnostics.
ASDA-A2R series catalog (EN) · Drive selection, ECML coil and magnet track options, and dimensional drawings.
For other Delta servo series, see the Delta servo PDF archive.
Editor’s Note
Ask for records from the original axis when buying used. Start with the complete drive model and serial number, the motor nameplate and a photo of the CN5 socket. For a machine-side replacement, save an ASDA-Soft parameter backup and the existing alarm history. During inspection and testing, a powered display is the first check. A trace from a compatible motor and scale lets you assess the feedback input as well.
Measure scale direction and scaling separately. Before enabling full-closed-loop control, follow the manufacturer’s procedure and compare the scale count with an independent position measurement over a safe range of travel. A count that changes in the opposite direction points to feedback polarity. An error that grows in proportion to travel points to a scaling or resolution mismatch. Then check home return repeatability. If AL040 appears, find where the scale and motor feedback diverge before changing the error limit.
For AL052 and AL058, start with initial pole detection. If AL052 appears on an installation without Hall sensors, check the scale feedback and mechanical friction. For AL058, see whether the controller issued a move before detection finished and how far the axis moved during detection. Make these checks within a safe travel range and account for the machine’s load conditions.
Check the cable carrier and scale when the fault repeats at the same position. Record where the feedback changes unexpectedly. Inspect the carrier bend at that point, connector contact, scale readhead gap and shield termination. Use a captured trace to assess signal noise and filtering after those checks.
Investigate fast stops and vibration separately. If AL002 occurs only during rapid deceleration, review stopping time, load and regenerative braking capacity together. If the axis shakes at a particular point in its travel, first check the slide, guides and cable drag. Once you identify the source of the mechanical vibration, compare the results of auto-tuning and servo gain adjustment.
Related Topics
Commands and motion: Pulse and direction signals · Supervisory control in servo systems · How servo motors work
Control loops and tuning: Speed loop gain · Servo control loops · Servo torque control
Other Delta Units
ASDA-A2 servo drives · ASDA-A2-E EtherCAT servo drives · ASDA-A3 servo drives · Delta AH motion controllers
Delta servo drive series · Used Delta automation equipment
External References
Delta ASDA-A2R user manual · Delta Electronics ASDA-A2R catalog