Delta DVP04DA-SL
Delta DVP04DA-SL – 4-Channel Left-Side Analog Output Module
Delta DVP04DA-SL adds four analog outputs to the left expansion bus of a compatible Delta DVP PLC. It can provide a speed reference to an inverter, a command to a proportional valve driver or an analog signal to a recorder. Select the output range for each channel individually.
Delta’s instruction sheet lists DVP-SV and DVP-EH2-L hosts. Its later programming table lists DVP-SV2 and EH2-L. Verify the full CPU code, left-bus support and module position. The similarly named DVP04DA-S uses a different connection and addressing arrangement.
Output modes and wiring
Mode 0 (H0000) ±10 V, −32,000 to +32,000. Mode 1 (H0001) 0–20 mA, 0 to 32,000. Mode 2 (H0002) 4–20 mA, 0 to 32,000. Mode 3 (H0003) 0–10 V, 0 to 32,000. Delta’s 2026 specification table gives 16-bit bipolar voltage resolution, 15-bit resolution for the other three ranges and a 250 µs per channel response.
Apply 24 V DC to the 24+ and 24− supply terminals. The specified supply range is 20.4–28.8 V DC. Use Vn+ / COM for voltage and In+ / COM for current on CH1–CH4. Voltage load impedance must be at least 1 kΩ. Total current-loop load must be 500 Ω or less. Analog channels share a reference without galvanic isolation between channels. Follow the manufacturer’s diagram for FG and protective grounding.
Match the receiving input and the channel mode when choosing 0–10 V or 4–20 mA. To reduce electromagnetic interference, route shielded analog cable separately from motor and relay wiring. Consider CPU scan time and the receiver filter alongside the module’s response.
WPLSoft, ISPSoft and channel addressing
PLC programming takes place in the host using WPLSoft or ISPSoft, depending on CPU support. For the SV2 models in Delta’s cable guide, connect PC USB to CPU COM1 RS-232 with UC-PRG020-12A. A PC with a serial port can use UC-MS020-01A. For SV and EH2-L, verify the cable and port for the CPU code.
The ladder program addresses left-side modules from K100 to K107, starting with the closest module to the CPU. CR#2–CR#5 select CH1–CH4 modes. CR#16–CR#19 hold CH1–CH4 output commands. Use TO to write and FROM to read. The model code in CR#0 is H4401. CR#43 holds the error status.
Bench example. With the module at K100, TO K100 K2 K2 K1 selects 4–20 mA for CH1. With table output disabled, TO K100 K16 K16000 K1 gives nominal 12 mA on CH1. In this mode K0 = 4 mA and K32000 = 20 mA. FROM K100 K43 D200 K1 reads the error word into example register D200.
Related topics and modules
Scale the PID percentage to the selected output range. Choose a suitable input module for feedback from a potentiometer, 0–10 V sensor or 4–20 mA sensor. Read a pressure sensor with suitable analog input and control hardware while the output sends an analog speed reference to the drive. Label analog reference wiring separately from industrial communication and RS-485 wiring.
DVP04AD-SL is a left-side analog input module. Compare output ranges and mounting side for DVP04DA-S, DVP04DA-S2 and DVP02DA-S. For a new panel, Derell PLCs and smart relays are separate control options.
Editor’s Note
On a used unit, inspect the SL suffix, left-bus connector and removable terminals.
At first power-up, check the 24 V supply and the ID in CR#0. Recheck the TO/FROM address if a module has been added or moved.
For a 4–20 mA test, connect a multimeter across a 250 Ω load resistor. Commands of 0, 16,000 and 32,000 give nominal readings of 1, 3 and 5 V.
If a command written to CR#16–19 does not appear at the output, check for active table output on that channel and other program writes.
If the error LED flashes, read CR#43. If the value drops under load, check total loop resistance and the COM return.
Test the output before enabling the field load. Verify the drive run enable and emergency stop circuit separately.
PDF documents and series links
See our Delta DVP PLC files page for installation, wiring and register tables. In the 2026 module manual, see printed page 11-3 for specifications, 11-10 for registers and 11-17 for wiring.
DVP04DA-SL · DVP Slim analog modules · DVP expansion modules · DVP PLC series · Used Delta PLCs · Delta Automation
External references
Delta DVP04DA-SL Instruction Sheet · Delta DVP Series Module Manual, 2026 · Delta PLC/HMI Cable Selection Guide