Delta DVP04TC-S
Delta DVP04TC-S Four-Channel Thermocouple Input Module
The Delta DVP04TC-S adds four thermocouple inputs to the right side of a compatible DVP Slim PLC CPU. Each channel can be set independently to type J, K, R, S or T. A single CPU can monitor temperatures at several points, such as oven zones, plastic moulds or packaging jaws.
Measurement ranges and wiring
Type J −100 to 700 °C, type K −100 to 1,000 °C, types R and S −10 to 1,700 °C, and type T −100 to 350 °C. These are the module’s input ranges. When selecting a probe, check the thermocouple type, sheath and operating temperature. Use the applicable thermocouple standards to check cable type and polarity.
The module uses a 24 V DC supply (20.4–28.8 V DC, 2 W maximum). Resolution is 0.1 °C and response time is 200 ms per channel. At 25 °C ambient, overall accuracy is ±0.5% of full scale. The module returns signed 16-bit temperature values and applies cold-junction compensation. Connect the external supply to 24V/0V and each probe to L+ and L− for its channel. Use SLD and Delta’s grounding diagram for the shield. Route the low-level analog signal wiring away from heater and drive power cables in the control panel.
PLC software, cable and temperature registers
On a compatible CPU such as the DVP-SS2 or DVP-SX2, write the PLC program in WPLSoft or in ISPSoft with CPU support. Check the COMMGR settings for ISPSoft. For a compatible CPU with an 8-pin mini-DIN RS‑232 port, use the UC-PRG020-12A cable. A PC without a serial port needs a suitable USB-to-RS‑232 adapter. The programming cable connects to the CPU.
Use TO to write the channel types in CR#1. J/J/J/J uses H0000 and K/K/K/K uses H0249. In normal measurement mode, read CR#6–9 for average temperatures and CR#14–17 for present temperatures in °C with FROM. CR#30 reports errors. A signed value of 253 represents 25.3 °C. The special module closest to the CPU is module 0. In standalone communications, the RS‑485 Modbus port supports ASCII or RTU. Delta specifies that this port is unavailable when the module is connected to the CPU side bus.
Multi-zone heating application
On a packaging machine, display the average jaw temperature on the HMI and log the channel error status alongside the temperature in SCADA. Maintenance can then distinguish a disconnected probe from a real temperature change. For PLC-based PID control, pass the measured value to the CPU’s PID loop. The heater uses a separate output stage. See the guides to temperature control with PID and solid-state relays for output selection.
Related models
For Pt100 probes, see the DVP04PT-S and DVP06PT-S. If changing the sensor type, review Pt100 and thermocouple differences. Two-input options include the DVP02TUR-S, DVP02TUL-S, DVP02TUN-S, DVP02TKL-S, DVP02TKR-S and DVP02TKN-S. Sensor and output options vary by model. For single-zone standalone control, see how a temperature controller works and browse Derell temperature controllers.
Editor’s Note
When buying used, ask for photos of the full model label, removable terminal block and side-bus connector.
Allow the 30-minute warm-up specified by Delta before checking the readings.
Move a known good probe through all four channels with the matching type selected. Where possible, compare the readings at room temperature and at a second reference point.
If the reading falls as the probe heats, check L+ and L− polarity first. If readings jump only when the heater switches, check the cable route and shield termination.
Leave one enabled channel open to check the error response. The four channel readings and CR#30 give you a practical record of the used module’s condition.
PDFs and technical documents
Related document index Delta DVP PLC files. In Chapter 9 of the DVP Series Module Manual dated 6 January 2026, specifications are on PDF pages 191–192, registers on 203–205 and wiring on 246. The 2014 model sheet includes English from PDF page 2 and Turkish from page 16.
DVP04TC-S main page · DVP Slim temperature modules · DVP expansion modules · DVP PLC series · Delta PLC · Used Delta models · Delta PLC and HMI manuals
External references
Delta DVP Series Module Manual (2026) · Delta DVP04TC-S Instruction Sheet (2022) · Delta DVP04TC-S Instruction Sheet (2014, TR/EN)