Delta DVP20EH00T2
Delta DVP20EH00T2 – DVP-EH2 PLC with 12 Inputs and 8 Transistor Outputs
The Delta DVP20EH00T2 is a compact PLC main unit in the DVP-EH2 series. It operates from 100–240 V AC, 50/60 Hz. The CPU has 12 digital inputs rated at 24 V DC and 8 NPN transistor outputs. Delta lists a program capacity of 16K steps for EH2. In machine automation applications such as part feeding, labelling and cut-to-length control, it can manage field signals, machine sequences and pulse-based positioning within one program.
Inputs, addressing and encoder connection
The built-in inputs are X0–X13 and the outputs are Y0–Y7. Addresses use octal numbering, so X10 follows X7. An inductive sensor can detect a metal target, a photoelectric sensor can detect a passing part and a limit switch can indicate end of travel. Match the S/S common to the sensor’s NPN or PNP output according to Delta’s sink/source wiring diagram.
The installation sheet specifies 200 kHz input bandwidth for X0, X1, X4 and X5, and 20 kHz for X10 and X11. Before connecting an encoder, check its signal level and the limits of the selected high-speed counter mode. When tracing PLC I/O, watch the terminal indicator and corresponding software address together.
Y0 and Y2 pulse outputs
Y0 and Y2 are the high-speed pulse outputs, rated up to 200 kHz. Delta shows an NPN open-collector output circuit for this model. Verify that the servo drive supports this signal type and the program’s pulse/direction format. Check the direction output and pulse scaling against the motion instruction in use.
The installation sheet specifies 5–30 V DC for the transistor output circuit. Resistive load limits are 0.5 A per point and 4 A per common. When switching an interposing relay, check the coil voltage, current and surge suppression. Follow the wiring drawing for field supply fuse protection and cabinet grounding.
Programming software and cable
Use WPLSoft with the EH2 CPU type to read, back up and monitor the ladder program. For ISPSoft, check that the installed version offers the EH2 CPU type, then configure the serial connection in COMMGR.
The PC connects through the 8-pin mini-DIN socket on COM1 RS-232. Delta PC-to-PLC serial cable options include DVPACAB215 (1.5 m) and DVPACAB230 (3 m). If the PC lacks a serial communication port, use a USB-to-RS-232 adapter with its driver installed and select the COM port assigned by Windows.
COM2 RS-485 is available for Modbus/RS-485 communication with an HMI or drive. Match the station address, baud rate, parity and ASCII/RTU selection to the existing program. Save a copy of the program and required retained data before online troubleshooting.
Editor’s Note
When buying a used unit, ask for a clear photo of the DVP20EH00T2 nameplate. Check the T2 suffix and AC supply rating.
On the bench, confirm that you can read the program through COM1. Save the existing program and required retained values before writing to the CPU.
If the encoder counts correctly at low speed and loses counts as speed rises, check the X address. X0/X1 and X10/X11 have different bandwidth ratings. Inspect the cable shield and filter settings as well.
Test the pulse channels on Y0 and Y2 individually. If the command is present and the drive stays still, check the input type, common connection and drive fault status.
If a Y indicator lights and the load stays off, isolate the machine loads and check the output common, DC supply and channel with a suitable bench test load.
When moving to EH3, verify the home sensor, travel limits, direction and pulse scaling before the first movement test. Keep the PLC backup with the drive parameters.
Related Delta models
The DVP20EH00R2 provides 12 inputs and 8 relay outputs in the same EH2 series. For a smaller transistor-output EH2, the DVP16EH00T2 has 8 inputs and 8 outputs. The DVP32EH00T2 has 16 inputs and 16 outputs. The DVP20EH00T3 is an EH3 model with 12 inputs and 8 transistor outputs. Before replacing a CPU, compare the project type, terminal layout and expansion modules.
OtomasyonAVM PDF files and internal references
Delta DVP PLC PDF Files · DVP-EH2 installation sheet – 20EH2 terminal layout (English PDF)
Delta DVP PLC series · Delta PLC overview · Used Delta equipment
External references
Delta DVP-EH2 installation sheet (2014) – wiring and electrical ratings · Delta DVP-PLC Application Manual – Programming (2014) · Delta ISPSoft and COMMGR serial connection guide