Heinrich Hertz

Heinrich Hertz and the experimental discovery of electromagnetic waves

Heinrich Hertz: What Two Sparks Revealed About Electromagnetic Waves

A spark jumps across a gap in a transmitter. Elsewhere in the room, a much smaller spark appears in a separate receiver. No connecting wire runs between them. For Heinrich Hertz, that tiny second spark became a way to investigate something invisible: the electromagnetic fields produced by a rapidly oscillating electrical discharge.

Heinrich Rudolf Hertz (1857–1894) was the German physicist whose experiments established a decisive link between electromagnetic theory and observable wave behaviour. His name survives in hertz, symbol Hz, the unit of frequency. His deeper legacy is the experimental evidence that helped make radio engineering possible.

The prediction waiting for an experiment

James Clerk Maxwell had developed a theory in which electricity, magnetism and light belonged to the same physical framework. Electromagnetic disturbances should propagate as waves. The challenge was to generate them deliberately and demonstrate their properties in the laboratory.

Earlier discoveries had already connected electricity and magnetism. Hans Christian Oersted showed that an electric current could deflect a compass needle. Michael Faraday developed experimental foundations for electromagnetic induction and the field concept, while Joseph Henry made important independent contributions to induction research. Hertz brought a further question into experimental reach: could electrical oscillations produce waves that travelled through space?

Inside the transmitter and receiver

In Hertz’s spark transmitter, an induction coil supplied a high voltage to conductors separated by a small gap. When the gap broke down, the discharge excited rapid, damped electrical oscillations. The arrangement radiated some of that energy into its surroundings.

One receiver design was a conducting loop interrupted by a very small adjustable gap. Fields from the transmitter produced an electrical response in the loop. Under suitable conditions, a tiny spark appeared at the receiver gap, providing a visible indication of that response.

The apparatus was simple enough to describe in a few sentences, but its interpretation required care. The repetition rate of the visible sparks was not the radio frequency. Each discharge could excite a short burst containing many much faster oscillations. Counting the transmitter’s clicks would therefore not reveal the oscillation frequency within those bursts.

Why a wireless spark was only the beginning

Two circuits can influence one another through nearby electric or magnetic fields. Observing an effect without a connecting wire does not, by itself, establish every property of a travelling electromagnetic wave. Hertz went further by investigating reflection, interference, standing waves and polarization.

Moving the receiver revealed positions where its response increased or decreased. Reflected and incident waves could combine to produce a standing-wave pattern. Changing the receiver’s orientation also mattered. These observations supplied evidence of an organised wave phenomenon, rather than an unexplained action at a distance.

Radio waves and visible light are both electromagnetic radiation. They share fundamental wave behaviour, but their frequencies and interactions with materials differ. A surface that reflects visible light well will not necessarily behave in the same way at every radio frequency.

Reading Hz correctly: frequency, period and wavelength

Frequency describes how often a periodic event completes a cycle. 1 Hz means one cycle per second. The prefixes simply scale that number: 1 kHz is one thousand cycles per second, 1 MHz is one million, and 1 GHz is one billion.

The time taken for one cycle is its period. The relationship is T = 1 / f. For a 50 Hz AC waveform, one complete cycle lasts 20 milliseconds. Frequency alone says nothing about the waveform’s voltage, the current it drives or the power delivered to a load.

For a wave, λ = v / f, where λ is wavelength and v is propagation speed in the medium. In a vacuum, v is the speed of light, c. Using approximately 300 million metres per second gives a wavelength of 3 metres at 100 MHz and 12.5 centimetres at 2.4 GHz. These are illustrative calculations, not specifications for a single historical Hertz apparatus.

From laboratory evidence to a communications system

Hertz’s experiments answered a fundamental physics question. A practical wireless link required additional engineering: encoding information, selecting a signal, detecting it reliably and extending its useful range. Pioneers including Guglielmo Marconi subsequently helped turn electromagnetic-wave research into working wireless telegraphy.

A modern Wi-Fi system belongs to that broader technological history, although its controlled oscillators, modulation methods and electronic receivers are far removed from a spark-gap experiment. Hertz established essential experimental foundations; later generations built the communication technologies around them.

The ultraviolet observation that opened another door

During his investigations in 1887, Hertz found that ultraviolet illumination could make an electrical spark easier to produce. This became an early landmark in the study of the photoelectric effect. Describing it as Hertz directly observing electrons leaving a metal would impose a later explanation on his original observation.

The modern account involves light transferring energy to electrons, which can escape from a material under suitable conditions. In 1905, Albert Einstein used the light-quantum hypothesis to explain the photoelectric effect. Hertz’s observation and Einstein’s explanation were distinct contributions made at different stages of the subject’s development.

One drive cabinet, several different frequencies

The unit named after Hertz appears throughout industrial electronics. On a variable frequency drive, an output-frequency reading normally refers to the fundamental electrical frequency supplied to the motor; the exact display meaning depends on the selected monitor parameter. The motor’s rated frequency is a separate nameplate specification describing its intended operating conditions.

Neither value is automatically the shaft speed. Converting electrical frequency into mechanical speed requires information about the motor, including its pole count. An induction motor also has slip, so its loaded shaft speed differs from the synchronous speed of the rotating field.

The same drive may use pulse-width modulation to generate its output. Its switching frequency describes a different activity from the motor’s fundamental supply frequency. A drive could, for example, produce a 50 Hz fundamental while using a 4 kHz PWM carrier, where that setting is supported. The shared unit does not make those two quantities interchangeable.

Fast switching transitions can also generate unwanted electromagnetic interference. Appropriate electromagnetic filtering, including correctly selected EMI filters, can help control conducted disturbances. Cable routing, shielding and bonding remain part of the solution. A filter cannot compensate for every installation problem.

A short life with a lasting experimental legacy

Born in Hamburg on 22 February 1857, Hertz carried out his landmark wave experiments in Karlsruhe during 1886–1888. He later worked in Bonn, where he died on 1 January 1894, aged 36.

His work offers a useful standard for technical investigation: turn a prediction into a measurement, vary the conditions, and check whether the result still supports the explanation. That habit remains valuable whether the subject is a radio receiver, an unstable sensor signal or interference inside a control cabinet. A visible symptom is a starting point; a discriminating test is what makes the explanation useful.

Sources: Heinrich-Hertz-Gesellschaft: life and work; KIT: Hertz’s electromagnetic-wave experiments; BIPM: SI units; Nobel Prize: explaining the photoelectric effect.