6ES5 300-5CA11

Siemens 6ES5 300-5CA11 – IM 300-5C Centralized Rack Expansion Interface

The 6ES5 300-5CA11 is an IM 300-5C interface for connecting EU 184U and EU 187U expansion units to S5-135U and S5-155U systems in a centralized configuration. Part of the SIMATIC S5 interface module range, it fits the interface slot on the central CPU side and works with an IM 312-5 in the expansion unit.

This arrangement serves expansion units without their own power supply. Operating power reaches the racks through the interface connection. When reviewing EU 184U versions such as the 184-3UA11 and 184-3UA21, check the installed rack's complete code and module layout. Up to three expansion units can be connected per interface branch, subject to cable and current limits.

IM 312-5 pairing and cable length

The expansion-side IM 312-5 has a permanently attached cable. The 312-5CA11 and 312-5CA12 belong to the 0.5 m cable group; the 312-5CA21 and 312-5CA22 belong to the 1.5 m group. These lengths do not describe an integral cable on the IM 300-5CA11 itself.

Plan the cable route and rack layout so that the total line length from the central interface to the last expansion interface on each branch does not exceed 2 m. A 1.5 m cable does not permit an unrestricted length of additional cable beyond it.

Power transfer and 5 A limit per connection

Siemens specifies a maximum permissible current of 5 A through each IM 300-5CA11 connection. This is not the module's own consumption. Check the PLC power supply capacity against the combined rack load. Place the highest-current rack close to the central unit and verify equipotential bonding between separate cabinets and the grounding arrangement.

Addressing and hardware version

Digital input, digital output and analog module addresses must match the PLC program and the rack's permitted configuration. Do not reuse central-unit addresses in an expansion unit. Preserve the normal or extended peripheral address-area selection required by the project.

The address-area setting depends on hardware version: versions up to 06 use jumpers; version 07 onward uses switch S1. Record the original card's version and settings before replacement. Do not copy jumper or switch positions between different versions by appearance alone.

Fault indicators and termination

The LD1/LD2 “I/O Module Failure” indicators illuminate when an expansion-unit module no longer responds to CPU access. During troubleshooting, check rack power, cable contacts, modules and address settings before concluding that the IM 300 itself has failed.

Unused IM 300-5 connections and the last IM 312-5 require no terminator. Do not apply the termination rule for the 300-3AB11 / IM 312-3 arrangement here. The 300-5LB11 serves a different rack and interface pairing. The 5CA11, 3AB11 and 5LB11 are not automatic substitutes. Disconnect system power before removal or installation.

Editor’s note

When looking for a spare, ask for the complete 5CA11 code rather than simply an IM 300. Similar-looking cards in this family serve different racks. Photographs of the original card and the expansion-side IM 312-5 make the conversation much easier.

Power for the expansion rack also passes through this connection. Give the cable and connectors a proper inspection. A poor contact or damaged connection can make a healthy card look faulty, so start with those simple checks.

Measure the whole route from the central rack to the last expansion rack and preserve the 2 m limit. Adjusting the rack position before installation is usually less trouble than stretching a cable just far enough to reach.

Photograph the jumpers or S1 before removing the old card. A replacement with a different hardware version may implement the same setting differently. A clear photograph of the working setup can save hours of searching later.

For a used card, ask for more than a clean appearance. Where practical, request an I/O transfer trial with a suitable rack and IM 312-5. Keep the original card labelled until the replacement is verified; it remains a useful reference if questions arise.

OtomasyonAVM resources and PDFs

+ Siemens S5 PDF archive: our documentation page. Use the S5-135U/155U System Manual below for this module's technical pairing.

+ S5 interface modules · S5 racks · S5 cable types

Related topics

+ 312-5CA11 · 312-5CA12 · 312-5CA21 · 312-5CA22: expansion-side interfaces with integral cables.

+ 300-3AB11 · 300-5LB11 · 301-5CA12: check connection function and rack pairing separately.

Browse SIMATIC S5

S5 interface modules · S5 racks · Siemens S5 PLC · Used Siemens equipment

Siemens and external references

+ Siemens S5-135U/155U System Manual – English, C79000-G8576-C199-07: pp. 2-4 and 7-2–7-9; central installation, IM 312-5 pairing, 2 m line limit, 5 A limit, indicators and version-dependent address settings.

+ Siemens S5-135U/155U Systemhandbuch – German, C79000-G8500-C199-07: p. 7-3; up to three expansion units per connection and the 5 A limit.

+ Siemens ST 50 · 1998 catalogue – English, p. 4/140: exact 300-5CA11 code, central-controller function and IM 312-5CA12/5CA22 cable options; third-party archive copy of a Siemens publication.