6ES5 581-1EA11

Siemens 6ES5 581-1EA11 — CP 581, 4 MB RAM and 2 MB Silicon Disk

Siemens 6ES5 581-1EA11 is a CP 581 basic board with an 80386SL processor at 25 MHz, 4 MB main memory and a 2 MB onboard silicon disk. This communications and data-processing board serves Siemens SIMATIC S5 installations, including suitable S5-115U, S5-135U and S5-155U hardware configurations.

The CP 581 works with the S5 CPU through the backplane bus to acquire, store and process data. For an industrial communication application, assess the installed operating system, application files and data exchange in the PLC program together. Replacing the board also requires preserving the software arrangement that makes it useful to the machine.

4 MB RAM and the 2 MB silicon disk

The 4 MB main memory is working RAM. The 2 MB silicon disk provides onboard flash-based storage. The related 6ES5 581-0EA11 is supplied without the onboard silicon disk. Equal main-memory capacity does not make these two part numbers equivalent hardware configurations.

The 6ES5 581-0HA11 memory expansion and S5 memory modules perform different roles. Inspect which memory and storage components are actually fitted to a used board. CP 581/486 part numbers such as 581-0EB11 and 581-1EB11 should also be distinguished from this 386 version; check software and accessory suitability against the complete part number.

COM connections, keyboard and display

The front panel has combined COM 1/COM 3 and KEYB/COM 2 connections, plus three coaxial RGB monitor sockets. Select S5 cables and adapters for this arrangement. When checking an interface, connector resemblance alone is insufficient grounds for using a standard PC cable.

Before removal, photograph the Y adapters and the keyboard and display connections. Labelling the existing cables in the SIMATIC S5 installation reduces confusion during a replacement trial. A missing picture alone does not identify a failed basic board; test the monitor, adapters and connection path separately.

Basic board, mass storage and AT slot

6ES5 581-0LA11 and 6ES5 581-1LA11 are separate CP 581 mass-storage modules. 6ES5 581-0RA11 is an AT-slot module. When buying a 581-1EA11 basic board, establish whether the complete assembly shown in the photographs is included or only the basic board.

An onboard silicon disk does not establish that machine-specific software is present. Preserve the installed MS-DOS environment, CP 581 system software and application files. Record the storage device’s boot role, drive configuration and existing contents before attempting installation or formatting.

Supply requirements and rack installation

Siemens specifies +5 V and +24 V supply rails for the 386-based CP 581. Maximum basic-board consumption is 1.8 A at +5 V and 0.1 A at +24 V. Include connected expansion modules when assessing the total load on the S5 rack.

Check the installation position against the central rack and any adapter casing. For an S5-115U installation, use the rack table in the CP 581 manual. A shared series designation does not establish that every slot or power-supply arrangement is suitable.

Configuration records and communication testing

During fault-finding, first identify the stage at which startup stops. Record the RUN, STOP, FAULT and SD-BUSY indicators together with screen messages. For Siemens S5 maintenance, check actual data exchange between the CPU and CP 581 rather than judging the installation from LEDs alone.

Before trying a replacement, record the SETUP and S5-page settings, drive definitions and application files. A working board from another machine may retain that machine’s configuration. Use the current installation’s working records as the reference and investigate differences before proceeding.

Editor’s note

Start with the 581-1EA11 identification label and fitted components. Similar front panels are insufficient for distinguishing 386 and 486 versions; read the complete part number.

If the board still starts, preserve the files and SETUP screens before removal. A replacement board only solves part of the problem when the machine’s original application is missing.

Do not immediately format an apparently missing silicon disk. Check the drive definition, startup messages and available backup first. An unnecessary write operation may destroy software that could otherwise be recovered.

For a missing picture, verify the RGB cable, monitor and Y-adapter positions separately. Photographs of the working arrangement are useful; avoid creating a second fault by swapping connections without a record.

For a used assembly, go beyond the startup screen and verify actual data exchange in a compatible S5 installation. Repeat after warm-up and establish which basic board, storage module, cables and software are included.

OtomasyonAVM resources and PDFs

See S5 communications modules, S5 cable types and About Siemens S5 PLC for related information. General system documents are collected in the Siemens S5 PDF archive. The English CP 581 manual covering the exact 581-1EA11 part number is linked below.

Related topics

+ 6ES5 581-0EA11 — CP 581 basic board without silicon disk.

+ 6ES5 581-1EB11 — CP 581/486 basic board with silicon disk.

+ 6ES5 581-0HA11 — CP 581 memory expansion.

+ 6ES5 581-1LA11 — CP 581 mass-storage module.

+ 6ES5 581-0RA11 — AT-slot module.

Browse SIMATIC S5

S5 communications modules · S5 auxiliary and expansion modules · SIMATIC S5 · Siemens S5 PLC · Used Siemens equipment

Siemens and external references

Siemens CP 581 — Manual, Volume 1, Release 03, 6ES5 998-2AT21 — English manufacturer manual. Model scope: PDF p. 4; basic board: printed p. 3-6 / PDF p. 107; supply ratings: printed p. 4-3 / PDF p. 217; processor and memory: printed p. 4-6 / PDF p. 220.

Siemens — EC Declaration of Conformity Khe001-04/2002 — PDF p. 5 lists 6ES5581-1EA11 as a 386-based CP 581 basic board with 4 MB and flash.