6ES5 581-0LA11
Siemens 6ES5 581-0LA11 CP 581 Mass Storage Module
Siemens 6ES5 581-0LA11 is the mass storage module for the CP 581 system within SIMATIC S5. Siemens’ 1993 hardware manual describes this order number with a 60 MB hard disk. When selecting this S5 supporting component, check the installed drive, board revision and existing software together.
The existing product entry states 16 MB, which differs from the manufacturer’s manual; the reason for this difference has not been established. Specify the supplied unit’s capacity from the drive label and system information. In an installation containing a 6ES5 581-0EA11 or 6ES5 581-0EB11, record the complete basic-board number as well.
Drive arrangement and related order numbers
The manual shows a 2.5-inch IDE hard disk, 3.5-inch floppy drive, LPT and COM 4. Evaluate these individually during acceptance. Distinguish this storage assembly from S5 memory modules, and identify the files that must be preserved before replacing a drive.
6ES5 581-1LA11, 6ES5 581-3LA11 and 6ES5 581-4LA11 have separate order numbers. Compare the basic-board connection, drive arrangement and software requirements before selecting a replacement. Record an AT-slot module such as the 6ES5 581-0RA11 separately; appearing alongside the storage module in a photograph does not establish what is included.
Installation, connections and supply checks
Photograph the arrangement in the S5 rack before dismantling it. Record the orientation of cables and connectors, fixing parts and adjacent boards. Avoid pulling a misaligned board into position with its fixing screw; inspect alignment and contact surfaces first.
When checking the S5 power supply, consider the combined load of the basic board and storage hardware. Label interface and communications connections before removal as well. If the first start fails, work through the supply, contacts and cable arrangement systematically.
Disk imaging and application preservation
Prepare separate backups for the SIMATIC S5 CPU program and the CP disk contents. Inventory the operating system, application files, startup settings and any licensing hardware. Create a complete disk image with suitable equipment before formatting the original drive or allowing repair utilities to write to it.
If the application uses digital input, digital output or combined I/O data, verify the monitored addresses when testing a copied disk. For analog records, compare raw values, scaling and timestamps with sample records. Successful booting alone does not demonstrate that the application performs every required task.
Used-unit acceptance and fault isolation
For an older Siemens S5 installation, evaluate a dismantled drive before introducing it into production equipment. Use a known suitable test arrangement to observe startup, file reading and application launch. Record repeated read errors, unusual noises and intermittent drive detection.
The quotation should state the complete order number, physical condition, installed drive, actual capacity, included cables and tests performed. Disclose replacement drives or other modifications. Identify untested connections and unreadable areas rather than treating them as working.
Editor’s note
The application on this drive may be more valuable than the hardware. Avoid starting with a clean installation simply because the old disk still spins. Preserve an image before planning repairs or replacement.
Check capacity beyond the headline in a listing. Record the board label, drive label and capacity reported by the system separately. A previous drive replacement may have changed what is actually installed.
Avoid repeated power cycling as an initial test. If the drive makes unusual noises or repeatedly stalls during reads, stop and assess its condition. Where important data is involved, avoid improvised actions that could make recovery harder.
Keep the small connection and mounting parts together during dismantling. Photographs of connector orientation, fixings and any settings help with reassembly. A replacement drive that looks similar still needs a compatibility check.
Startup text on the screen is only the beginning of a useful acceptance test. Check that the application launches, required files can be read and expected data exchange works. Record the basic board used and the operations tested.
OtomasyonAVM resources and PDFs
+ 6ES5 581-0LA11 product and information page and Siemens S5 models.
+ OtomasyonAVM shared SIMATIC S5 PDF archive. The relevant edition of the CP 581 hardware manual is linked in the external references below.
Related topics
+ CP 581 basic board 581-0EA11, 581-0EB11 and the 581-0RA11 AT-slot module.
+ S5 connection accessories, S5 memory modules and about Siemens S5 PLC.
Browse SIMATIC S5
S5 supporting modules | SIMATIC S5 | Siemens S5 models | Siemens second-hand homepage
Siemens and external references
+ Siemens CP 581 Manual, Volume 1 Hardware, 1993, English archive copy. 6ES5 998-2AT21, Release 03; 0LA11 scope, Section 3.2 and technical table 4.2.8.
+ Siemens CP 581 User Manual, 08/1999, English. A comparison reference for later 3LA11/4LA11 hardware; do not transfer those versions’ specifications to the 0LA11.