6ES5 431-7LA11

Siemens 6ES5 431-7LA11 — 16-Channel 24–48 V UC Digital Input Module

Siemens 6ES5 431-7LA11 is a 16-channel, 24–48 V UC (AC/DC) digital input module for SIMATIC S5 S5-115U/H systems. Optocoupler-based galvanic isolation is arranged in four groups of four inputs. Its ability to read both AC and DC field signals distinguishes it within the S5 digital input module range.

Suitable circuits provide PLC status information through relay contacts, contactor auxiliary contacts and field devices with matching signal levels. Relay sockets and wiring form part of the signal path. The module reads inputs; driving a load requires a suitable digital output module.

Signal levels and input current

The defined input voltage ranges are 0–5 V for logic “0” and 13–60 V for logic “1”. Voltages above 5 V and below 13 V lie outside these defined ranges. The 13–60 V detection range does not replace the nominal voltage specification. The ST 50 catalog specifies 47–63 Hz for AC operation.

Typical input current at logic “1” is 8.5 mA at 24 V AC or 9 mA at 24 V DC. The manual specifies 10.5 mA at 48 V AC or DC. These are input consumption figures, not output load ratings.

Group isolation and connections

Each group of four inputs shares its group return. Follow the manufacturer’s L1/N or L+/M connection diagram. Siemens does not permit connection of different phases on this model. Four isolated groups do not establish permission to use different phases.

Assess grounding, signal returns and S5 field cables separately. With two-wire sensors, check off-state leakage current as well; the AC/DC designation alone does not establish compatibility with every sensor.

Delay, cable length and address checks

Input delay is 2–13 ms for a 0→1 transition and 10–25 ms for a 1→0 transition. The manual’s maximum cable lengths are 1000 m shielded and 600 m unshielded. Overall response also includes the PLC program and scan time.

Record the S5 rack position together with the existing input addresses. Sixteen inputs provide two bytes of channel information. During PLC debugging, compare the field signal, channel LED and program input bit, and verify addressing against the existing project.

Differences from nearby models

6ES5 430-7LA12 has 32 inputs for 24 V DC, while 6ES5 420-7LA11 is a non-isolated 32-input option. 6ES5 432-7LA11 belongs to the 48/60 V UC signal class. Differences in channel count and voltage prevent automatic substitution.

6ES5 435-7LA11 is a 115 V UC input module. 6ES5 431-4UA12 belongs to the different S5-135U/155U hardware family. Check the 7LA11 suffix, signal voltage and existing wiring together.

Editor’s note

Take a moment to check more than “16-input S5” on the description. Matching the full 431-7LA11 code and the actual AC/DC field voltage helps avoid ordering the wrong card.

If four inputs disappear together, give the module a fair check before replacing it. Start with that group’s shared return, wire and terminals.

Do not distribute different phases across the groups simply because isolation is provided. The manufacturer does not permit it on this model; an existing installation should still be checked.

If an input stays on after its contact opens, investigate sensor leakage and residual cable voltage. Photograph the wiring and keep a program backup before removal; isolate the supply and verify absence of voltage before changing connections.

When buying a used digital I/O module, test all 16 channels and every one of the four groups with a suitable setup. Check that the program bit changes correctly as well as the LED.

OtomasyonAVM resources and PDFs

For family background, see about Siemens S5 PLCs; manuals are available in S5-115 PDF files. The exact model’s technical table appears on page 15-22 of the S5-115U manual.

Related topics

+ 6ES5 430-7LA12 · 6ES5 432-7LA11 · 6ES5 435-7LA11 · 6ES5 431-4UA12 · PLC debugging

Navigation: SIMATIC S5 | Digital input modules | S5 racks | Used digital I/O | Siemens

External references

+ Siemens S5-115U Manual — 15-22, 431-7LA11 specifications, wiring and phase restriction (English)

+ Siemens ST 50, 1998 — 3/30–3/32, technical comparison and ordering data (English)