6ES5 712-8AF00
6ES5 712-8AF00 Siemens SIMATIC S5 712 IM 316 Connecting Cable, 0.5 m
The Siemens 6ES5 712-8AF00 is a 0.5 m SIMATIC S5 712 connecting cable for two IM 316 interfaces or two IM 316F interfaces in a configuration specified by Siemens. It extends the I/O bus from one mounting tier to the next in S5-90U, S5-95U and S5-100U systems. In the S5 cable range, the 8AF00 suffix identifies the 50 cm version.
In a cabinet, the cable can link the interface on the CPU’s mounting rail to the interface for an I/O group on the tier above. The digital inputs and digital outputs on that tier remain on the same I/O bus. The cable runs from OUT on the preceding interface to IN on the next one.
Which S5 and ET 100U configurations use this cable?
Siemens lists the 8AF00 as an IM 316 accessory in the S5-90U, S5-95U and S5-100U manuals. Appendix A.1.5 of the S5-95F manual lists the cable with the 6ES5 316-8FA12. For an F system, check the interface order number and connection layout against the approved hardware list for the installation.
On an ET 100U station with an IM 318-8 station interface, the cable is used for the IM 316 link between tiers within the station. The ET 100U manual specifies up to four tiers and 16 bus units in total for this layout. Each tier has one interface module.
How do you connect OUT to IN?
Connect OUT on the preceding IM 316 to IN on the next tier. Secure each plug with its two retaining screws. Siemens specifies that the screws hold the plug in place and make contact with the cable shield.
A separate ribbon cable connects the IM 316 to the last bus unit on the same tier. Check that connection on bus units such as the 700-8MA11 with screw terminals and 700-8MA22 with crimp terminals. If the interface has been removed and refitted, inspect the local ribbon cable and the 712 link between rails separately.
How do you select the cable length and order number?
The 8AF00 is 0.5 m, the 8BC50 is 2.5 m, the 8BF00 is 5 m, and the 8CB00 is 10 m. Measure the route through the cable duct and allow for the way each plug enters its socket. For several tiers, check the installation manual for the system before choosing the cable lengths.
The IM 315 set comes with two interfaces permanently joined by a 0.5 m cable. The 8AF00 is the order number for the detachable 712 cable on the IM 316. The 6ES5 734-2BD20 serves the PG connection. Match the full 712-8AF00 code on the cable label when ordering.
Editor’s note
Before removing the cable from a SIMATIC S5 cabinet, record both interface labels and which OUT and IN sockets it connects.
Measure the full cable route through the duct between the DIN rails, including the approach to each socket. Leave enough slack to keep strain off the plugs.
If every module on an expansion tier is offline, check the incoming 712 link, the local ribbon cable and the power supply to that tier.
If a reading is wrong on a single analog module, start with the channel terminal and field signal. If other modules are also affected, check the shared bus connection.
Replace the cable with the system powered down. Before restarting, check both sets of retaining screws and the order of the tiers. On the S5-100U, I/O slot numbering continues across tiers.
OtomasyonAVM resources and PDFs
SIMATIC S5 cables and connectors · S5 interface modules · S5 mounting rails and racks
OtomasyonAVM S5-90 PDF page · OtomasyonAVM S5-115 PDF archive
Related topics
6ES5 712-8BC50, 2.5 m cable · IM 316 6ES5 316-8MA12 · IM 316F 6ES5 316-8FA12
S5 navigation
SIMATIC S5 › S5 cables and connectors
External references
Siemens S5-100U system manual, Section 3.1.2 and Appendix D · Siemens S5-90U/S5-95U system manual, IM 316 ordering table
Siemens S5-95F system manual, Appendix A.1.5 · Siemens ET 100U distributed I/O manual, Chapter 2 and Section 3.1.2 · Siemens ST 50 catalog, IM 315/316/316F, p. 2/76