6ES5 512-5BC21
Siemens 6ES5 512-5BC21 — AS 512 Serial Communications Expansion Board
The Siemens 6ES5 512-5BC21 is an AS 512 serial communications expansion board for SIMATIC S5. It adds three interfaces: two passive TTY current-loop channels and one channel selectable between TTY and V.24. It belongs to the S5 interface module range and operates with the basic board.
The 6ES5 512-5BC12 basic board provides one serial interface; adding the 5BC21 creates an AS 512 arrangement with four interfaces in total. Keep this distinction in mind when selecting an S5 communications module: the 5BC21 is not a standalone replacement for the basic board.
TTY, V.24 and transmission speed
For V.24 operation, check the RS-232 electrical interface and the connected device. The differences between RS-232, RS-422 and RS-485 remain relevant: serial data alone does not establish electrical compatibility.
A miniature switch on the board sets each interface’s speed. The Siemens ST 53 catalogue specifies a maximum combined transmission rate of 9600 baud across the interfaces in use. This is a combined limit, not a simultaneous 9600-baud allowance for every channel.
Active current-loop operation requires a 24 V DC supply through the front connections. Verify the S5 cable, active/passive arrangement and pin assignment together. Compare shielding and grounding with the existing installation as well.
Program and connected-device settings
AS 512 supports data exchange with computers, printers, data terminals and other automation devices. Review channel definitions and data areas in the PLC program alongside the connected device’s settings. During troubleshooting, identify which device belongs to each channel first; changing a board does not resolve a configuration mismatch.
System and slot compatibility
The Siemens ST 53 ordering table lists this code for S5-150A, S5-130W, S5-150K and S5-150S arrangements. Check the rack and slot layout for the particular system. Membership of the S5 family does not establish compatibility with every S5 rack.
The S5-150U central controller manual separately documents the AS 512 basic/expansion pair: basic board in slot 89 and expansion board in slot 99. It also states that slot 79 must be occupied for AS 512 operation. Do not apply this layout unchanged to other chassis.
Finding a CPU 924, CPU 925, CPU 926 or CPU 927 in the installation is only part of the identification. Record the complete central-controller number, basic board, slot arrangement and program before selecting a replacement.
Related codes and board roles
The 511-5AA12 and 511-5AA14 belong to the PG programmer-interface range. AS 511 and AS 512 serve different purposes; the 5BC21 is the AS 512 communications expansion board.
When comparing older 512 codes such as 512-5AA12 and 512-5AA21, check the full suffix and basic/expansion role. Similar board appearance does not establish direct interchangeability between 5AA and 5BC versions.
Editor’s note
Start with the important distinction: 5BC12 is the basic board; 5BC21 is the expansion board. A photograph showing both labels helps avoid a wrong purchase. A request for an “AS 512 card” alone leaves too much room for misunderstanding.
If one channel has stopped, check that channel’s cable, connected device and switch settings before condemning the whole board. Record whether the other channels still work. That small observation can narrow the fault considerably.
Keep a clear record of the active and passive sides of each current loop. If nobody knows which end supplies the loop current, changing cables at random makes the investigation harder. Draw the existing connection first, then compare it with the diagram.
Photograph the miniature switches, wiring and slot numbers before removal, and back up the program. Switch off power and follow the system manual when replacing the board. Having the original settings to hand makes the replacement much easier to assess.
When buying used equipment, ask where possible for actual data-exchange tests on all three additional channels. A successful check on one channel does not prove the other two. Share the basic-board number and connected-device details at the outset so the replacement and test arrangement can be matched properly.
OtomasyonAVM resources and PDFs
+ About Siemens S5 PLCs · S5 interface modules · S5 communications modules
+ Siemens S5 PDF files — our manual archive. Siemens references for the AS 512 technical description and complete ordering code appear at the bottom of this page.
Related topics
+ 512-5BC12 basic board · 512-5AA12 · 512-5AA21 · 511-5AA12 PG interface
Browse SIMATIC S5
+ S5 interface modules · S5 communications modules · S5 cables and connectors · SIMATIC S5 · Siemens second-hand equipment
Siemens and external references
+ Same catalogue — 9/3: 6ES5 512-5BC12 and 6ES5 512-5BC21 ordering and system table