6ES5 373-0AA21
Siemens 6ES5 373-0AA21 SIMATIC S5 373 EPROM Memory Submodule, 16 KB
The Siemens 6ES5 373-0AA21 is a 373-series EPROM memory submodule that stores the user program in a SIMATIC S5 system. It holds 16 KB (16,384 bytes), equivalent to 8,192 STEP 5 instructions in Siemens’ specifications. Siemens lists this order number for the S5-130W and S5-150A/K. Each system mounts the submodule differently.
The EPROM retains its programmed contents when power is removed. Before replacing the submodule, read the blocks from the EPROM and save the current program from the S5 CPU separately. The installed EPROM may predate changes made to the running program.
Installation in the S5-130W and S5-150A/K
The S5-130W Version B manual shows the 373 submodule fitted to an EPROM socket on the 6ES5 921-3WB11 central processor board. In a two-EPROM installation, record which submodule occupies the upper and lower sockets. The CPU assigns the lower submodule the address immediately following the upper one.
In the S5-150A/K, Siemens specifies the 350 memory board and a 6ES5 983-0BA11 spacer adapter. Jumpers on the 350 board in the S5 rack set the EPROM start address. When two EPROM areas are used, their address ranges must be contiguous and free of overlaps.
Reading, programming and erasing
The PG 615 manual lists the 373-0AA21 by order number. Siemens specifies the 6ES5 984-0UA11 adapter for programming it on a PG 670. Reusing a programmed EPROM requires a UV eraser. Check that the memory is blank before writing, then read it back and compare the contents with the source file.
When servicing S5 communications processors, check the COM 530 module selection and the hardware socket specification separately. COM 530 lists the 373-0AA21 for data transfer with the PG 615. For the memory socket on a compact CP 530 or a block-format CP 530, use the table for the installed processor’s order number.
Identifying similar EPROM submodules
The 373-0AA41 is the 32 KB version in the 373 EPROM family. The PG 615 system table lists the 373-0AA61 under S5-150S. The 373-1AA21 is a 16 KB CMOS EPROM. The 373-1AA41, 373-1AA61 and 373-1AA81 are CMOS EPROM variants with different capacities.
The 372-0AA51 and 372-0AA61 belong to the separate 372 series. The PG 615 manual lists the 375-0LA15, 375-0LA21 and 375-0LA41 under S5-100U, S5-101U and S5-115U. Match the series and socket as well as the capacity when selecting a spare.
Editor’s note
Record the complete order number. Take a label photo that clearly shows 373-0AA21. The suffix distinguishes it from the 1AA21 of the same capacity.
Make a separate backup of the running program. Use the appropriate S5 programming cable to retrieve the CPU blocks. Keep the EPROM readback as a separate file for the same machine.
Check which adapter you need. The 983-0BA11 fits the 350 memory board. The 984-0UA11 fits the PG 670 programmer.
Document socket positions and jumpers before removal. Photograph the upper and lower positions on the S5-130W or the address jumpers on the 350 board in the S5-150A/K. Switch off the system before removing or fitting the submodule.
Check the EPROM contents and the installation separately. First confirm that the programmer can read the EPROM and that it contains the expected blocks. Then check the socket, adapter and address settings on the machine.
OtomasyonAVM resources and PDFs
SIMATIC S5 memory submodules · About Siemens SIMATIC S5 PLC systems
OtomasyonAVM Siemens SIMATIC S5 PDF manual archive
Related topics
S5-130W Version B CPU 921 · 373-0AA41 32 KB EPROM · 373-1AA21 16 KB CMOS EPROM
Browse SIMATIC S5
Siemens SIMATIC S5 · S5 memory cards · SIMATIC S5 CPUs
Siemens and other external references
Siemens SIMATIC S5-130W Version B manual (German PDF) (373 EPROM and PG 670 adapter)
Siemens 350 memory board and 370/372/373 submodule instructions (German PDF) (S5-150A/K table, capacity and addressing)
Siemens PG 615 programming device manual (German PDF) (Table 2.9 and module selection)
Siemens SINEC L1 manual, COM 530 and PG 615 memory transfer (English PDF)