6ES5 318-8MC12
Siemens 6ES5 318-8MC12 – ET 200U IM318-C PROFIBUS DP/FMS Interface
The 6ES5 318-8MC12 is an IM318-C slave interface module connecting an ET 200U station to PROFIBUS DP/FMS within the SIMATIC S5 product family. Siemens identifies this function in its exact-order-number data sheet. Within the ET 200 system and S5 interface module range, it provides the station's communication interface.
It provides the communication path between suitable ET 200U digital input, digital output and analog modules and the higher-level controller. The slave station and master hardware configuration must match. Fitting the module physically is only part of establishing communication.
DP and FMS communication
The IM318-C family combines PROFIBUS DP and FMS functionality on the same bus connection. In DP operation, the master reads input data and sends output data. FMS operation requires its associated communication configuration. When reviewing PROFIBUS, check the physical connection and selected protocol separately.
PROFIBUS connectors, the bus cable, termination and grounding all belong in a communication check. Identify the end station before adjusting termination; do not change it by guesswork. Check the shield connection and cable ends as well as the connector's seating.
Master and station configuration
Assess a spare alongside the CPU, master interface and existing project. If the master side uses a module such as the IM308-C 6ES5 308-3UC21, record its full code and revision too. Compare the I/O mapping in the PLC program with the station's actual module sequence.
The 318-8MA12, 318-8MB11, 318-8MB12 and 318-8MB13 are separate order numbers. The 8MA, 8MB and 8MC suffixes matter. Do not copy another 318 model's switch positions or communication settings directly to the 8MC12; check the protocol and revision being used.
Commissioning and maintenance checks
Before replacement, record the station address, switch positions, module sequence and existing project. Check the PLC power supply and cable connections. Disconnect the supply before removing the interface module. On restart, confirm that the master detects the station, then verify the input and output data mapping.
During troubleshooting, distinguish loss of the entire station from a single failed I/O channel. Check the supply and bus connection first, followed by the address and configuration. Our ET 200 system overview provides general context; interpret the LEDs according to the selected operating mode.
Editor’s note
Photograph the old module's label and switches before replacing it. The details seem easy to remember while the board is in your hand, but they can slip away when the job takes longer than expected. A photograph can save hours of reconstructing settings.
Before ordering a replacement for a bus fault, work through the cable, connector and termination. A loose connection in an older cabinet can make a healthy module look faulty.
Check that the spare actually carries the 318-8MC12 code. “It is another 318” is too little information. The suffix, revision and protocol deserve a careful look.
If the master project is available, back it up before starting. Changing a module may take minutes; reconstructing a lost station configuration can take much longer. Keep a record of the original settings.
For a used spare, ask for more than illuminated LEDs. Where practical, check communication with a master and actual I/O data exchange. Keep the original module labelled until the system has been checked in operation.
OtomasyonAVM resources and PDFs
+ S5 interface modules and Siemens ET 200: related systems and module pages.
+ PROFIBUS connectors and PLC troubleshooting: connection and maintenance information.
+ Siemens ET 200 manuals and Siemens S5 PDF archive: our available documentation pages. The 1993 ET 200U manual below explains IM318-C family operation; its exact-code scope includes 8MC11. The 8MC12 identity is separately confirmed by its Siemens data sheet.
Related topics
+ 318-8MA12 · 318-8MB11 · 318-8MB12 · 318-8MB13: selecting the full 318-family order number.
+ 308-3UC21 IM308-C · What is PROFIBUS? · What is grounding?
Browse SIMATIC S5
S5 interface modules · Siemens ET 200 · Siemens S5 PLC · ET 200 manuals · Used Siemens equipment
Siemens and external references
+ Siemens 6ES5318-8MC12 data sheet record – English, 28 April 2018: IM318-C, ET 200U, PROFIBUS DP/FMS slave identification.
+ Siemens ET 200U Distributed I/O Station Manual – English, EWA 4NEB 812 6087-02b, Edition 03: Chapters 5 and 6, DP/FMS operation and diagnosis.