What is Profibus ?

PROFIBUS industrial fieldbus communication

PROFIBUS, derived from Process Field Bus, is an industrial fieldbus communication system designed for digital data exchange between controllers and field devices. It has been widely used to connect PLCs, remote I/O, motor drives, sensors, actuators and process instruments in factory and process automation.

In simple terms: PROFIBUS allows one industrial controller to communicate with many devices over a common fieldbus. A PLC can read field inputs, send commands to drives or output modules and receive operating or fault information without requiring a separate point-to-point communication link for every device.

What does PROFIBUS mean?

The name PROFIBUS comes from Process Field Bus. It is not an abbreviation for “professional data communication system.” PROFIBUS belongs to the wider family of industrial communication technologies used to exchange control and diagnostic data between automation equipment.

PROFIBUS communication is specified within IEC 61158 Type 3 and IEC 61784 CPF 3. Its best-known forms are PROFIBUS DP and PROFIBUS PA. PROFIBUS FMS also existed historically, but DP and PA became the most important implementations in industrial automation.

What is PROFIBUS DP?

PROFIBUS DP stands for Decentralized Peripherals. DP is not an abbreviation for “Data Protocol.” It was developed for fast communication between a central controller and distributed equipment such as remote I/O, valve terminals, weighing systems and AC drives.

The most common copper transmission technology for PROFIBUS DP is based on RS-485. Standard transmission rates range from 9.6 kbit/s to 12 Mbit/s. The available segment length decreases as the communication rate increases, so baud rate, cable type, topology and termination must be considered together.

In a practical machine, the PLC may send run commands, speed references and control words to a PROFIBUS-connected variable frequency drive. The drive can return actual speed, current, status words and fault information over the same bus. These values can then be displayed to the operator through an HMI panel.

Real industrial drives have used this approach for many years. For example, the ABB ACS550 family supported PROFIBUS DP through optional fieldbus interfaces alongside several other industrial communication systems.

What is PROFIBUS PA?

PROFIBUS PA stands for Process Automation. It is intended primarily for process field instruments such as pressure, temperature, flow and level transmitters, analysers and valve positioners.

A common PROFIBUS PA transmission technology is MBP — Manchester Coded Bus Powered. It operates at 31.25 kbit/s and can supply suitable field instruments through the same pair of conductors used for communication. This can significantly simplify wiring in installations containing many industrial sensors and transmitters.

PROFIBUS PA can also be used in appropriately engineered hazardous-area installations. However, the presence of PROFIBUS PA does not by itself make a system explosion-safe. Field devices, power supplies, barriers, installation methods and the applicable protection concept must all be suitable for the hazardous area.

What is the difference between PROFIBUS DP and PROFIBUS PA?

PROFIBUS DP is mainly associated with factory and machine automation, where relatively fast cyclic communication is required. PROFIBUS PA is designed around process instrumentation, bus-powered field devices and process-plant requirements.

The two technologies can also operate within the same control system. A DP/PA coupler or link can interface a high-speed DP network with PA field segments. A single PLC and HMI automation system can therefore integrate machine equipment and process instrumentation through different PROFIBUS physical layers.

How does PROFIBUS communication work?

Traditional PROFIBUS documentation describes active stations capable of initiating communication as masters, while field devices controlled by a master are described as slaves. These terms remain common in installed systems and older manuals even though newer industrial documentation may use controller/device terminology.

In a typical single-master installation, a PLC exchanges process data cyclically with the configured field devices. In a multi-master network, communication rights between active stations are coordinated using a token-passing mechanism. Each master then communicates with its assigned field devices.

This structure allows digital inputs, output commands, drive control words and process values to be exchanged predictably. Information collected by the controller may subsequently be presented through an HMI or forwarded to a higher-level SCADA system for monitoring and production supervision.

What are cyclic and acyclic PROFIBUS communications?

Cyclic communication is used for process I/O that must be exchanged continuously between the controller and field devices. Inputs, outputs, drive commands and operating values are typical examples.

Acyclic communication is used for information that does not need to be transferred during every bus cycle. Device parameters, maintenance information and detailed diagnostics can be accessed this way when the device and PROFIBUS service support it.

For this reason, descriptions that present “Cyclic Data Exchange, Event-Driven Data Exchange and Acyclic Data Exchange” as three separate PROFIBUS protocols are misleading. PROFIBUS DP is better understood through its cyclic process communication, acyclic services, diagnostic functions and the DP-V0, DP-V1 and DP-V2 extensions.

What are PROFIBUS DP-V0, DP-V1 and DP-V2?

DP-V0 provides the core cyclic I/O exchange and diagnostic functions of PROFIBUS DP. DP-V1 adds acyclic data communication and alarm handling, allowing controllers and engineering systems to access additional parameters and device information.

DP-V2 adds further capabilities including clock synchronization and time-stamping functions for more demanding automation applications. The fact that a product has a PROFIBUS DP interface does not automatically mean that it supports every DP-V1 or DP-V2 service; the actual device specification must be checked.

What is a PROFIBUS GSD file?

GSD is the standardized device description used by PROFIBUS engineering systems. It describes communication-related characteristics such as supported baud rates, module structures, input/output data sizes and diagnostic capabilities.

When a remote I/O station or PROFIBUS motor drive is added to a PLC project, the engineering software may require the correct GSD file before the device can be configured.

A GSD file does not configure an entire installation automatically. The bus address, hardware modules and PLC I/O mapping still have to correspond to the actual equipment installed in the machine.

How is PROFIBUS DP wired?

A conventional RS-485 PROFIBUS DP segment is normally installed as a linear bus. Suitable shielded twisted-pair PROFIBUS cable is used, with devices connected along the segment rather than through uncontrolled long star branches.

The electrical PROFIBUS RS-485 system supports transmission rates from 9.6 kbit/s to 12 Mbit/s, and a conventional electrical segment supports up to 32 bus stations. Repeaters can be used to divide a larger network into additional electrical segments.

Communication cable should also be routed carefully around high-power equipment. Long parallel runs beside contactor wiring, motor cables or PWM outputs from frequency converters can increase the risk of EMC-related communication faults.

Why is PROFIBUS termination important?

RS-485 PROFIBUS segments require termination at the two physical ends of the bus. PROFIBUS termination should not be reduced to the general statement “put a 120-ohm resistor across A and B.” Conventional PROFIBUS DP termination uses an active resistor network rather than a single passive resistor.

Many PROFIBUS connectors include an ON/OFF termination switch. Termination should normally be enabled at the first and last stations and disabled at intermediate stations. Incorrect termination is one of the first physical-layer issues to inspect when a previously working network becomes unstable.

Because the termination network requires power, switching off the device at the physical end of a bus can also remove its active termination. This detail is particularly important in plants where individual machines or panels are routinely isolated while the remainder of the network remains in service.

When was PROFIBUS developed?

The development of PROFIBUS began with a German joint project in 1987, when companies and institutes worked together to develop and test an open fieldbus standard. The PROFIBUS Nutzerorganisation e.V. — PNO was then founded in Germany in 1989 to continue the work and promote standardization.

PROFIBUS later developed into an internationally standardized industrial communication technology. Today the wider technology community operates through PROFIBUS & PROFINET International — PI, supporting PROFIBUS, PROFINET and other industrial communication technologies.

Is there a universal PROFIBUS programming code?

No. PROFIBUS is not normally implemented by copying a universal block of C, Python or PLC code into a controller. The implementation depends on the PLC manufacturer, PROFIBUS interface, protocol stack, engineering software and whether the device is operating as a master or field device.

In many PLC systems the PROFIBUS network is primarily configured through the hardware configuration or engineering environment. The engineer imports the required device description, assigns addresses, selects modules and maps the process data into PLC memory. The PLC application then reads and writes the mapped I/O variables.

More specialized functions such as acyclic parameter access or detailed diagnostics may require manufacturer-specific function blocks or communication services. A generic “PROFIBUS code example” without identifying the controller, interface and software environment can therefore be more misleading than useful.

What is the difference between PROFIBUS and PROFINET?

PROFIBUS and PROFINET are different industrial communication technologies. PROFIBUS is a traditional fieldbus system. PROFIBUS DP commonly uses an RS-485 serial bus, while PROFIBUS PA uses transmission technology designed for process instrumentation.

PROFINET, by contrast, is based on Ethernet technology. It uses an Ethernet-oriented network architecture and provides its own controller/device model, device naming, real-time communication and diagnostic mechanisms.

It is therefore incomplete to describe PROFINET simply as “a faster version of PROFIBUS.” PROFINET generally provides much more network bandwidth, but the technologies also differ in physical infrastructure, topology, engineering and communication behaviour.

A newer technology is not automatically the correct replacement for every working system. Existing equipment, required cycle time, spare-parts availability, maintenance knowledge and migration cost should be evaluated before replacing an established PROFIBUS network.

In modern industrial automation projects, Ethernet-based communication may offer substantial integration advantages. Existing PROFIBUS equipment, however, can often remain in service or be integrated into Ethernet-based systems through suitable gateways or proxies.

Where is PROFIBUS used?

PROFIBUS DP can be found in manufacturing machinery, conveyors, packaging systems, distributed I/O, motor-control installations and many other factory automation applications. PROFIBUS PA is commonly associated with process instrumentation in industries such as chemical processing, water treatment, energy and other continuous-process plants.

A typical automation architecture may collect signals from sensors, exchange commands and status information with motor drives, process the information in the PLC and then display operating data on an HMI or supervisory SCADA system.

The presence of a PROFIBUS connector alone does not guarantee complete interoperability between any two devices. Supported profiles, GSD data, bus address, baud rate, module structure and controller capabilities still have to match the application.

Related Industrial Communication Guides

Industrial Communication · What Is Ethernet? · Modbus FAQ

Related Automation Pages

PLCs and Modules · HMI Panels · SCADA · AC Drives and VFDs · Sensors