• Gemo PC109A

Gemo PC109A is a microprocessor-based PID temperature profile controller designed for processes that require several temperature and time stages. Up to 20 separate steps can be programmed, with a maximum time of 18 hours for each step. OtomasyonAVM has been supplying Gemo products since 2013.

Front dimensions: 96 × 96 mm.
Standard supply: 220 VAC.
If a 24 V supply version is required, this should be specified when ordering.
Output: Relay output as standard. If an SSR output version is required, please specify this when ordering.

Selectable sensor inputs: J, K and S type thermocouples and Pt100.

Depending on the application, the PC109A can be used with a J type thermocouple, push-in J type thermocouple or Pt100.

The PC109A is intended for applications where one fixed temperature setting is not enough. Different temperature targets and holding times can be arranged as a sequence and run automatically.

Temperature profile control

The controller can store up to 20 programmable steps. Each step can have its own temperature setting and operating time.

Maximum step time: 18 hours per step.

A profile can be used to heat the process to one temperature, hold it there for a specified time, then continue automatically to the next programmed temperature and time stage.

PID and Auto-Tune

The PC109A supports P, PI, PD and PID control as well as ON/OFF operation.

Auto-Tune: The Auto-Tune function can be used to calculate suitable PID parameters automatically from the process response.

Anti-windup: Helps prevent excessive integral accumulation during PID control.

Alarm: Relative or absolute alarm operation can be selected.

Process monitoring

The front display allows the operator to monitor the SET value, Process value, active Step number and Remaining Time at the same time.

This is particularly useful during long multi-stage processes, as the current stage and remaining time can be checked directly from the controller.

Sensor and measurement functions

Thermocouple inputs: J, K and S type T/C.
Resistance sensor: Pt100.
T/C compensation: Ambient temperature compensation.
Pt100 compensation: Line compensation.

For a comparison of these sensing methods, see thermocouple vs. Pt100.

The controller uses stored °C/mV and °C/Ω conversion tables for sensor curve correction.

Offset: A correction value can be added to the measured process value.

Program protection and memory

Password protection: Parameter access can be protected against unwanted changes.
Memory: Program and control parameters remain stored when power is removed.

Connection: Plug-in terminals make wiring and controller replacement easier.

Relay and SSR applications

Relay output is suitable for normal switching applications. Where the heater needs to be switched frequently, an SSR output version may be more suitable.

This is particularly relevant when PID control uses frequent time-proportional switching, where reducing mechanical relay operation can be useful.

Control panel installation

The PC109A can be installed in industrial panels together with AC drives and speed controllers. Thermocouple and Pt100 wiring should be kept separate from motor and inverter power cables where possible.

Temperature-sensor signals are relatively sensitive to electrical noise, so sensible cable routing and shielding help maintain stable measurement.

Other compatible sensing products can be found in our industrial sensors section.

Gemo PC109A User Manual (PDF)

Gemo price list
Gemo contact information
Gemo main page
Industrial control devices

Installation: Sensor, supply and output wiring should be carried out by qualified technical personnel.

Before applying power, check the selected sensor type, supply voltage, output configuration and programmed temperature profile against the product documentation.

Write a review

Note: HTML is not translated!
Bad Good

Gemo PC109A

  • 54.00USD

  • Ex Tax: 54.00USD

Related Products

 DGP-77R-A Step Temperature Controller

DGP-77R-A Step Temperature Controller

DGP-77R-A Step Temperature Controller DGP-77R-A is a step temperature controller with..

48.00USD Ex Tax: 48.00USD

 DGP-99R-A Process Control Device

DGP-99R-A Process Control Device

DGP-99R-A Process Control Device DGP-99R-A is a 220V powered process control device with ..

42.00USD Ex Tax: 42.00USD

 DGP-77T-A Step Temperature Controller with SSR Output

DGP-77T-A Step Temperature Controller with SSR Output

DGP-77T-A Step Temperature Controller with SSR Output DGP-77T-A is a compact step tempera..

49.00USD Ex Tax: 49.00USD

DGP-99T-A Step Profile Temperature Controller

DGP-99T-A Step Profile Temperature Controller

DGP-99T-A Step Profile Temperature Controller 220V AC Power Supply | 1 SSR + 1 Relay Output ..

50.00USD Ex Tax: 50.00USD