• Gemo PC107A

Gemo PC107A is a 72 × 72 mm programmable PID temperature profile controller for processes that require several temperature and time stages. Up to 20 steps can be programmed, with a maximum duration of 18 hours for each step. OtomasyonAVM has been supplying Gemo products since 2013.

Front dimensions: 72 × 72 mm.
Standard supply: 220 VAC.
A 24 V supply version is available when specified at the time of order.
Output: Relay output as standard. If an SSR output version is required, this should be specified when ordering.

Selectable sensor inputs: J, K and S type thermocouples and Pt100.

Depending on the application, the PC107A can be used with a J type thermocouple, push-in J type thermocouple or Pt100.

The PC107A is intended for processes where one fixed temperature setting is not enough. Different temperature targets and holding times can be programmed as a sequence and run automatically.

Temperature profile control

The controller supports up to 20 programmable steps. Each step can have its own temperature SET value and operating time.

Maximum step time: 18 hours per step.

A typical profile can heat the process to one temperature, hold it there for a set time and then continue automatically to the next programmed temperature stage.

PID and Auto-Tune

The PC107A supports P, PI, PD and PID control as well as ON/OFF operation.

Auto-Tune: The Auto-Tune function can calculate suitable PID parameters automatically from the process response.

Anti-windup: Helps limit excessive integral accumulation during PID control.

Alarm: Relative or absolute alarm operation can be selected.

Process monitoring

The controller can display the SET value, Process value, active Step number and Remaining Time at the same time.

This is especially useful during long profile programs, as the operator can see both the active stage and its remaining time directly from the controller.

Sensor and measurement functions

Thermocouple inputs: J, K and S type T/C.
Resistance sensor: Pt100.
T/C compensation: Ambient temperature compensation.
Pt100 compensation: Line compensation.

For more information on these sensing methods, see thermocouple vs. Pt100.

The controller uses stored °C/mV and °C/Ω conversion tables for sensor curve correction.

Offset: A correction value can be added to the measured process value.

Program protection and memory

Password protection: Parameter access can be protected against unwanted changes.
Memory: Program and control parameters remain stored when power is removed.
Connection: Plug-in terminals make wiring and controller replacement easier.

Relay and SSR applications

Relay output is suitable for normal switching applications. Where frequent heater switching is required, an SSR output version may be more suitable.

This is particularly useful in time-proportional PID applications where frequent switching would otherwise increase mechanical relay wear.

Control panel installation

The PC107A can be used in industrial control panels together with AC drives and other switching equipment. Thermocouple and Pt100 wiring should be kept separate from motor and inverter power cables where possible.

Temperature-sensor signals are relatively sensitive to electrical noise, so sensible cable routing and shielding help maintain stable measurement.

Gemo PC107A User Manual (PDF)

Gemo price list
Gemo contact information
Gemo main page
Industrial control devices

Installation: Sensor, supply and output wiring should be carried out by qualified technical personnel.

Before applying power, check the selected sensor type, supply voltage, output configuration and programmed temperature profile against the product documentation.

Write a review

Note: HTML is not translated!
Bad Good

Gemo PC107A

  • 55.00USD

  • Ex Tax: 55.00USD

Related Products

 DGP-77R-A Step Temperature Controller

DGP-77R-A Step Temperature Controller

DGP-77R-A Step Temperature Controller DGP-77R-A is a step temperature controller with..

48.00USD Ex Tax: 48.00USD

 DGP-99R-A Process Control Device

DGP-99R-A Process Control Device

DGP-99R-A Process Control Device DGP-99R-A is a 220V powered process control device with ..

42.00USD Ex Tax: 42.00USD

 DGP-77T-A Step Temperature Controller with SSR Output

DGP-77T-A Step Temperature Controller with SSR Output

DGP-77T-A Step Temperature Controller with SSR Output DGP-77T-A is a compact step tempera..

49.00USD Ex Tax: 49.00USD

DGP-99T-A Step Profile Temperature Controller

DGP-99T-A Step Profile Temperature Controller

DGP-99T-A Step Profile Temperature Controller 220V AC Power Supply | 1 SSR + 1 Relay Output ..

50.00USD Ex Tax: 50.00USD