Delta DVP-F485
Delta DVP-F485 is an RS-485 COM3 function card for the DVP-EH3 CPU slot. It adds a two-wire serial communication port while the CPU’s built-in COM2 remains available. Delta specifies this model for EH3. The older DVP-F485S associated with DVP-EH2 has a separate order code. Check the CPU label, card code and slot together before replacement.
The card provides industrial communication over an RS-485 link with an HMI panel, AC drive or compatible servo drive. EH3 can use COM3 as a master or slave. Match the peer’s Modbus RTU or Modbus ASCII mode. For a SCADA connection, also verify the driver protocol and station address.
Terminals, termination and installation
D+ and D− are the RS-485 differential pair. SG is the signal reference. Check the peer device’s A/B polarity in its manual. Use shielded twisted-pair cable and route it away from drive motor wiring inside the control panel.
Bridging N1 and N2 connects the built-in 120 Ω resistor across D+ and D−. Fit the bridge when the card is at a physical end of the bus and needs termination. Avoid adding a second 120 Ω resistor at the same end. Leave N1 and N2 open at an intermediate node. With the power isolated, insert the card vertically into the EH3 slot, secure it and check the terminal label.
COM3 settings, software and cable
D1109 sets the COM3 serial format. M1136 retains the setting. The EH3 application manual gives M1320 ON for RTU and OFF for ASCII on COM3. Its example uses D1109 = H87 for 9600 bit/s, 8 data bits, even parity and one stop bit. Use those example settings only when the peer matches them. Keep the existing PLC program’s COM2 setting in D1120 separate.
Delta’s general serial communication manual lists up to 115,200 bit/s for COM3. The PLC Link application note discusses 500 kbit/s separately for EH3 with DVP-F485. Choose a field bus speed supported by the peers. Station numbers and register maps depend on the connected model. See the drive Modbus address example and Modbus FAQ.
Open the EH3 project in WPLSoft or a CPU-compatible version of ISPSoft. Check COMMGR for an ISPSoft connection. For initial access, you can use the CPU’s COM1 RS-232 port with a suitable PLC programming cable. Delta’s guide lists UC-PRG020-12A and a suitable USB–RS-232 option. Verify the CPU’s connector when selecting a Delta cable.
For a PC connection to COM3, Delta shows the IFD6500 USB–RS-485 or IFD8500 RS-232–RS-485. Verify the USB adapter driver and COM port number. Card detection and automation logic are handled through the host PLC project. The application manual identifies a detected F485 as D1149 = 13.
Related cards and topics
DVP-F232 provides RS-232, DVP-F422 provides RS-422 and DVP-FEN01 provides Ethernet. DVP-FPMC serves a different field network. Compare the CPU slot, physical interface and protocol when choosing a card. See communication converters and used communication modules for related equipment.
DVP-F2AD and DVP-F2DA are analog function cards. For Delta AS PLCs, select the serial card for the specific AS host.
Editor’s Note
Check whether the full label reads F485 or F485S. If EH2 and EH3 units share a workbench, keep the cards sorted by their full codes.
With power isolated, check the connector, mounting screw and all five terminals. If the CPU fails to detect the card, start with the slot and connector contact.
Begin with one field device and a short cable. Match D+/D−, serial format and station number, then read a known register.
If the link works on the bench but times out in the panel, inspect the N1–N2 bridge, cable route and SG reference. Change one variable at a time.
For a used card, ask for label and terminal photos. On the bench, check D1149, then read data repeatedly over COM3. Card detection and a working link are separate checks.
PDF manuals and technical documents
Use the Delta DVP PLC files page to find the EH function card instructions, DVP-PLC programming manual and PLC/HMI cable guide. Look for DVP-F485 for the terminal drawing and EH3 COM3 for the serial settings.
DVP-F485 main page · DVP function cards · DVP expansion modules · DVP PLC series · Delta PLC · Used Delta models · Delta manuals
External references
Delta DVP-EH function card instruction sheet · Delta DVP-PLC programming manual · Delta PLC/HMI cable selection guide · Delta PLC Link application note