Faq For PID Control
Experiment with proportional, integral and derivative action using a simplified closed-loop process model.
Simulation Settings
Feedback: 0.00 | PID Output: 0.00 % | Error: 0.00
Graph: Setpoint is shown in red, process feedback in blue and PID output in green. You can change the setpoint or Kp, Ki and Kd while the simulation is running.
Important: This is an educational first-order process simulation. It is intended to demonstrate PID behaviour, not to generate tuning values for a real motor, furnace, pressure system or production machine.
Hello dear colleagues,
Why Should We Understand PID Control?
PID control is one of the most widely used feedback-control methods in industrial automation. The same basic idea appears in temperature regulation, pressure control, flow, level, motor speed, position control and many other systems: measure the difference between the desired condition and the actual condition, then continuously act to reduce that error.
Its widespread use does not mean that one set of Kp, Ki and Kd values will work everywhere. The behaviour of a PID loop depends on the process itself: how quickly it responds, how much delay it contains, whether it naturally settles at a new operating point, how noisy the sensor is and how the actuator behaves near its physical limits.
PID is therefore better understood as a closed-loop relationship between sensor, controller, actuator and process rather than simply as a mathematical equation containing three gains.
The Basic PID Feedback Loop
Every PID system begins with a desired value, usually called the setpoint (SP). The actual measured value is the process variable (PV) or feedback value.
The basic control error can be written as:
Error = Setpoint − Process Variable
The proportional, integral and derivative terms use the present error, accumulated error and rate of change to generate a controller output.
That output is applied to an actuator such as a valve, heater, motor drive, servo or power controller. The actuator changes the physical process, the sensor measures the new condition and the controller calculates again.
That repeated correction is what turns PID from an equation into a feedback-control system.
What Does Proportional Action Do?
The proportional term reacts to the error that exists right now. A large error produces a stronger correction, while a small error produces a smaller response.
Use the P-Only Mode button in the simulation to remove integral and derivative action. Try changing Kp and observe how the response changes.
With a low Kp the process responds gently but may remain far from the setpoint. Increasing Kp usually makes the response stronger. If proportional action becomes too aggressive for the process dynamics, however, overshoot and oscillation can appear.
This is one of the first lessons of PID tuning: faster is not automatically better.
What Does Integral Action Do?
Some processes settle with a small persistent error when proportional control is used alone. Integral action accumulates the error over time and continues adjusting the output until that remaining offset is reduced.
This is extremely useful, but excessive integral action can create another problem. The controller may continue carrying the memory of earlier error even after the process has begun approaching the setpoint.
The result can be overshoot, slow cycling or, when the actuator has reached a physical limit, integral windup.
Real industrial PID implementations therefore need sensible output limits and some form of anti-windup behaviour.
What Does Derivative Action Do?
Derivative action responds to how quickly the controlled variable is changing. In suitable processes it can add damping and reduce overshoot.
However, derivative action also reacts strongly to measurement noise. A sensor that jumps slightly from one sample to the next may cause an unnecessarily nervous controller output when Kd is high.
This is why not every PID application actually needs all three terms. Many industrial temperature, flow and level loops operate very effectively as PI controllers.
Why Disturbance Rejection Matters
A controller should not be judged only by how well it follows a new setpoint. Real industrial processes are constantly disturbed.
A furnace door opens. Another consumer connects to a pressure header. Additional load is applied to a motor. Flow into a tank suddenly changes.
The Apply Disturbance button in the simulator suddenly reduces the feedback value. This provides a simple way to compare how different Kp, Ki and Kd settings recover from the same disturbance.
A good controller should reject disturbances without creating excessive overshoot, repeated cycling or unnecessary actuator activity.
PID Tuning Is More Than Reaching the Setpoint
When evaluating a control loop, several characteristics should be considered together:
- Rise time,
- Overshoot,
- Settling time,
- Steady-state error,
- Disturbance rejection,
- Actuator movement,
- Time spent at output limits,
- Sensitivity to measurement noise.
This is why Kp, Ki and Kd tuning is not simply a race to obtain the fastest possible response.
A useful industrial controller needs an appropriate balance between performance and robustness.
Why Does the Same PID Tuning Not Work Everywhere?
A storage-tank level loop, an industrial furnace and a servo axis have completely different physics.
A level process may behave as an integrating system. A furnace can have a large time constant and considerable thermal delay. A servo axis may react in milliseconds but contain inertia, elasticity and mechanical resonance.
The controller screen may show Kp, Ki and Kd in all three cases, but the meaning of an aggressive or conservative tuning is not the same.
For this reason, different process dynamics require different PID tuning approaches.
Dead Time: The Delay the Controller Cannot See Through
If there is a delay between changing the controller output and seeing the resulting movement in the sensor, the controller temporarily has no information about the effect of its latest action.
An overly aggressive controller may continue correcting during this blind period and create a much larger process movement once the delayed response finally becomes visible.
Sensor filtering, PLC scan time, communication, valve movement and physical transport through the process can all contribute to this delay.
The effect of these delays is discussed in more detail under time delays and system dynamics in PID control.
PID Is Not the Solution to Every Control Problem
PID is extremely versatile, but it is not automatically the best strategy for every process.
Large dead time, strong nonlinear behaviour, interacting variables or rapidly changing process dynamics may justify additional techniques such as cascade control, feedforward, gain scheduling, adaptive control or model-based methods.
The differences are examined in PID control and other control strategies.
PID Control Is Not a Safety System
A well-designed PID loop can improve process stability and help keep operating conditions within the desired range. That does not make the PID controller a functional safety system.
Independent over-temperature protection, emergency stopping, safety valves, Safe Torque Off and other functions intended to protect people or machinery may require separate and appropriately designed safety systems.
Normal process control and safety protection should not be treated as the same engineering layer.
Why Use a PID Simulation?
Changing PID parameters randomly on a real machine can be expensive, disruptive or unsafe. A simple simulation allows the effect of different settings to be observed without risking physical equipment.
Try the following experiments:
Experiment 1: Set Ki = 0 and Kd = 0. Increase Kp from 0.5 to 1, 2 and 4. Compare the resulting response.
Experiment 2: Keep Kp fixed and gradually increase Ki. Observe steady-state error, settling and overshoot.
Experiment 3: Change the setpoint from 50 to 70 while the simulation is running.
Experiment 4: Apply the same disturbance with several different tunings and compare recovery.
Experiment 5: Try to obtain a similar feedback response using different combinations of Kp and Ki. This demonstrates why there is often no single magical set of PID numbers.
PID Control Topics
The following pages form the complete OtomasyonAVM PID control topic network. They cover PID fundamentals, implementation platforms and different controlled process variables.
1- PID Fundamentals and Tuning
- What Is PID Control?
- How Does a PID Controller Work?
- Proportional, Integral and Derivative Components
- How Are Kp, Ki and Kd Adjusted?
- Time Delays and System Dynamics
- Conditions for Stable and Accurate PID Control
- PID Tuning for Different Process Types
- Common PID Control Problems
- Real-Time PID Control Challenges
- PID and Other Control Strategies
- Limitations of the PID Control Algorithm
2- PID Platforms and System Integration
- PID Control with PLCs
- PID Control with Microcontrollers
- PID Control with Arduino
- PID Control with Raspberry Pi
- PID Control with FPGA
- PID Control with Industrial PCs
- Cloud-Based PID Control
- PID Control with SCADA
- PID Control in Robotics
- PID Control with Servo Motors
3- Process Variables Controlled with PID
- PID Control for Temperature
- PID Control for Pressure
- PID Control for Speed
- PID Control for Level
- PID Control for Flow
- PID Control for Position
- PID Control for pH
- PID Control for Humidity
- PID Control for Light
- PID Control for Vibration
- PID Control for Torque
- PID Control for Power
- PID Control for Current
- PID Control for Density
- PID Control for Viscosity
- PID Control for Frequency
- PID Control for Color
- PID Control for Odor
- PID Control for Sound
- PID Control for Radiation
4- Direct Industrial PID Applications
- PID Control with a VFD
- PID Control with a Temperature Controller
The Most Important Lesson in PID Control
Learning PID does not mean memorizing Kp, Ki and Kd values. The useful skill is learning to read the process.
When controller output changes, does the measurement react immediately or only after a delay? Does the process settle naturally at a new value, or continue ramping? Is the sensor noisy? Is the actuator saturated? Is the controller requesting movements the physical system cannot actually produce?
Without answering these questions, repeatedly changing PID coefficients may only hide the real problem.
Good PID tuning begins before the gains are changed. It begins by understanding what the process trend is telling us.
This section is intended to explain the fundamentals of PID control and provide organized access to the related PID topics on OtomasyonAVM. Parameters used on real machines and industrial processes should always be selected according to process dynamics, sensor and actuator behaviour, controller implementation and the safety requirements of the application.
Refine Search
- Cloud-Based PID Control
- How does a PID controller work?
- How should PID control parameters be adjusted for different types of processes?
- How to regulate (Kp, Ki, Kd) in PID controller?
- PID control and stable operation?
- PID Control for Color
- PID Control for Current
- PID Control for Density
- PID Control for Flow
- PID Control for Frequency
- PID Control for Humidity
- PID Control with Servo Motors
- Real-time PID control?
- Time factor in setting PID parameters?
- What are common problems with PID controllers?
- What are the differences between PID and other control strategies?
- What are the limitations of the PID control algorithm?
- What do the (P, I, D) of the PID algorithm mean?
- What is PID?