What Is Loop Impedance Measurement?

Line-to-earth fault loop impedance measurement

Will an earth fault disconnect the supply in time?

Earth fault loop impedance describes the complete path that current would take if a live conductor touched an exposed metal enclosure. The path runs from the source to the fault and back through the protective return path. Its impedance, Zs, is measured in ohms. The practical question is whether enough fault current will flow to operate the protective device within the required disconnection time.

An earthing connection alone does not answer that question. The reading must be considered alongside the protective device's operating principle and selection requirements. There is no universal pass value for every circuit. The earthing arrangement, trip characteristic and applicable installation rules determine the assessment.

Know which part of the installation you are testing

In a TN system, the main return path normally uses metallic PE or PEN conductors back to the earthed supply point. The loop includes the source winding and outgoing line conductor. In a TT system, the installation electrode, soil path and source electrode contribute to the loop. An earth fault does not always return mainly through soil.

Loop impedance, electrode resistance and protective-conductor continuity are separate checks. A low Zs cannot certify an individual electrode or every PE connection. Checking earthing at a socket requires more than recognising an earth contact.

For a simple TN circuit with negligible reactance, Zs ≈ Ze + R1 + R2: external supply-loop impedance plus the line and circuit protective-conductor resistances. Parallel paths, conductor temperature and reactance may make this approximation unsuitable for a complex installation.

A larger impedance means less fault current

Using Ohm's law, the approximate prospective earth fault current is If ≈ U0 / Zs, assuming negligible impedance at the fault itself. U0 is nominal line-to-earth voltage: typically 230 V on a 230/400 V supply. This is prospective fault current, not normal load current or standing leakage.

Same voltage, different fault currents — U0 = 230 V
Zs Estimated fault current Lesson
0.50 Ω 460 A Lower impedance allows more fault current.
1.00 Ω 230 A Doubling impedance halves the current.
2.00 Ω 115 A Trip performance depends on the protective device.

Consider a C16 MCB. Using the upper edge of its magnetic operating band gives 10 × 16 = 160 A. A 2 Ω loop produces an estimated 115 A, so this calculation does not establish guaranteed magnetic operation. B, C and D curves differ at the same current rating. Devices covered by IEC 60898 and fuse-links covered by IEC 60269 require their own operating characteristics.

For disconnection by overcurrent protection, the basic relationship is Zs × Ia ≤ U0. Ia ensures operation in the specified time; it is not the device's nominal current rating. It comes from the applicable time-current curve or verification table. The illustrative C16 calculation, 230/160 ≈ 1.44 Ω, is not a ready-made acceptance limit: voltage factors, operating temperature, measurement uncertainty and the prescribed verification method still matter.

Choose the test mode to suit the circuit

A loop tester applies a controlled load to an energised circuit and calculates impedance from the voltage response. L–PE testing assesses the earth fault path; L–N testing assesses the line-neutral path. A line-neutral result cannot substitute for an earth-loop result.

A high-current L–PE test may operate an RCD. Compatible instruments offer a low-current no-trip mode; two- or three-wire connections depend on the method. “No-trip” describes the test's purpose, not an unconditional guarantee of uninterrupted power. Existing leakage and other causes of RCD operation may still cause a trip. Assess the effect on critical loads before testing.

A loop test does not verify RCD trip time. MCBs, RCDs and RCBOs provide different functions. Separate RCD testing must suit its rated residual operating current and AC, A, F or B classification. In TT installations, earth fault current may be too low for rapid fuse or MCB operation. RCD-based fault protection requires assessment of RA × IΔn ≤ UL and the applicable disconnection time. RA represents the installation electrode and protective-path resistance; UL is the applicable touch-voltage limit. IT systems require a separate first- and second-fault assessment.

A plausible reading can still hide a problem

Loose joints, corrosion, long cable runs and inadequate conductor sizes can increase impedance. Connection maintenance matters, while supply fluctuations and electrical noise may produce unstable readings. Parallel metallic paths can lower impedance and conceal a defect in the intended PE conductor. Continuity verification remains necessary. Near a limit, consider uncertainty and test conditions, not simply decimal places.

Increasing the breaker rating can make prompt fault disconnection harder. Changing the protective-device type requires a fresh check of cable protection, load and disconnection time. A low impedance can mean a high prospective fault current; the device must also have sufficient breaking capacity for the relevant fault level at its location.

A useful test record includes the circuit and test point, earthing arrangement, voltage, Zs, calculated fault current, protective-device rating and settings, test mode, instrument identification and verification status, acceptance criterion and conclusion. IEC 61557-3 addresses measuring-equipment requirements; installation acceptance follows relevant IEC 60364 provisions and applicable local rules.

Technical sources: IEC 61557-3 | Megger: loop testing | Schneider Electric: TN | Schneider Electric: TT | Circuit-breaker characteristics