6ES5 755-0AA13

Siemens 6ES5 755-0AA13 — SINEC H1 Transceiver

Siemens 6ES5 755-0AA13 is a 755 transceiver for the SINEC H1 network. Used in Siemens SIMATIC S5 installations, this auxiliary network component provides the physical connection between the station’s network interface and the H1 bus.

An error reported by an S5 communications module does not identify the processor as the failed component. In industrial communication, the CP interface, connecting cable, transceiver and main bus are separate checkpoints. Start by determining whether the fault affects one station or the wider network.

10 Mbit/s SINEC H1 and the triaxial bus

Siemens’ H1 network manual describes a 50 Ω triaxial bus based on IEEE 802.3 / 10BASE5. This Ethernet infrastructure has a transmission rate of 10 Mbit/s. The stated segment limits are 500 m of cable and up to 100 transceivers; these are network design limits.

When replacing a cable, assess more than its appearance or connector fit. Consider differences between Ethernet cable types and the H1 cable’s screening arrangement. Main-bus accessories such as the 6ES5 755-4AA11 N-type coaxial connector set must match the installed cable and assembly method.

A triaxial bus segment requires 50 Ω termination at both ends. When inspecting accessories such as 6ES5 755-3AA11 terminators, establish where the actual segment ends are and whether both terminations are present. Termination faults can appear as intermittent communication errors affecting several stations.

Station interface and screening

The H1 manual describes the transceiver separating bus signals into transmit, receive and collision signals at the station’s AUI interface. The S5 connecting cable therefore needs to be assessed for contact quality, screening and the associated equipment’s supply arrangement, as well as mechanical condition.

Check cable screens, enclosure connections and reference arrangements against the H1 installation instructions. During a grounding inspection, follow the existing diagram rather than joining screen layers or adding connections arbitrarily. Corroded contacts, crushed cables and loose connections can imitate a device fault.

Transceivers, repeaters and protocols

6ES5 755-1AA12 is a repeater part number in the same 755 group. Transceivers and repeaters perform different tasks, so a shared series designation does not establish interchangeability. Modern Ethernet switch and hub terminology should not be treated as a direct description of every component in the installed H1 bus.

A physical connection alone does not establish application communication. Assess the protocols operating over Ethernet against the CP and the remote station. 6ES5 755-0AA13 should not be treated as a standalone protocol converter. For example, a PROFINET connection requires suitable communication hardware and protocol support as well as a compatible physical interface.

CP matching and communication testing

If installation records identify CPs such as 6ES5 535-3LB11 or 6ES5 535-3LB12, record the complete processor part number together with the existing connection arrangement. The description “S5 compatible” is insufficient for selecting a transceiver; compare the CP interface, cable, network medium and original device label.

Before changing the SIMATIC S5 installation, back up the Siemens S5 project and communication parameters. Preserve station addressing and connection records according to the existing CP configuration. Changing working settings while replacing a physical component can make the original fault harder to identify.

During fault-finding, inspect cables and connections before moving on to the transceiver and CP. Compare communication status in the PLC program with actual data exchange. An illuminated LED or a successful continuity check alone does not establish reliable communication between two stations.

Editor’s note

Start with photographs of the CP, transceiver and cable identification. Similar-looking components in an older H1 installation may perform different tasks; the 755 designation alone is not enough to select a replacement.

For intermittent communication, inspect the bus ends and terminations early. Replacing a working CP because of a missing terminator or loose coaxial connection adds expense while leaving the original fault in place.

Plan for the possibility that work on the main bus affects other stations. Mark the cable route and connections before removal, and preserve bus continuity and the original arrangement during replacement.

Check the supply using the appropriate CP and connection documentation. Do not apply a guessed voltage to the connector. Include loose or corroded contacts when investigating an apparent supply problem.

For a used unit, verify actual data exchange between two known-good stations and repeat the test after warm-up. A connection that fails when the cable moves slightly should not be accepted as serviceable merely because it works when held in one position.

OtomasyonAVM resources and PDFs

See S5 communications modules and About Siemens S5 PLC for system background. General manuals are collected in the shared Siemens S5 PDF archive. English and German references for the SINEC H1 triaxial network are provided below.

Related topics

+ 6ES5 755-1AA12 — SINEC H1 repeater.

+ 6ES5 755-3AA11 — bus terminators.

+ 6ES5 755-4AA11 — N-type coaxial connector set.

+ 6ES5 535-3LB11 · 6ES5 535-3LB12 — CP 535 communications processors.

Browse SIMATIC S5

S5 auxiliary and expansion modules · S5 communications modules · SIMATIC S5 · Siemens S5 PLC · Used Siemens equipment

Siemens and external references

Siemens SIMATIC NET — Manual for Triaxial Networks, Release 04 — English SINEC H1 network manual. Chapter 2 covers network architecture, transceiver functions, connections and termination. Network limits: printed p. 2-5 / PDF p. 21.

Siemens SIMATIC NET — Handbuch für Triaxialnetze, Ausgabe 04 — German manufacturer manual for the same network topic. Model-specific supply and mechanical ratings for other transceivers in these manuals should not be transferred automatically to 6ES5 755-0AA13.