6ES5 450-8MB11

Siemens 6ES5 450-8MB11 – 4-Channel Isolated Digital Output Module, 24–60 V DC / 0.5 A

The 6ES5 450-8MB11 is a SIMATIC S5 digital output module with four transistor outputs, designed for 24–60 V DC loads at 0.5 A per channel. It is used with S5-90U, S5-95U and S5-100U controllers and ET 100U and ET 200U I/O systems. Part of the S5 digital output range, its four channels form one optocoupler-isolated group.

The permissible load supply range is 20–72 V DC, switching current is 5 mA–0.5 A per channel, and the combined output current is 2 A maximum. Check compatibility with the CPU and small S5 module family using the complete ordering code.

Load supply and field connections

24–60 V DC describes the load supply range; the module does not convert voltage. Select the power supply to match the connected loads. Follow the module's diagram for the field wiring and check L+, M and the grounding arrangement. The four outputs are not four individually isolated channels.

Check continuous current and inrush when selecting an interface relay or another coil load. The relay coil's voltage must match the module's L+ supply. Select circuit fuses and cable protection to suit the load circuit.

Electronic protection and red F indicator

The outputs have electronic short-circuit protection. The output circuit can switch on automatically once the short circuit has cleared, so allow for the load becoming energised again. The red F indicator reports a short circuit or missing L+ load supply. An illuminated F indicator alone does not establish that the module is faulty.

Reading faults in an S5-100U program

The S5-100U manual describes fault reporting through I X.0 and I X.1. I X.0 reports the short-circuit/load-supply fault category; I X.1 reports a defective module, specifically a shorted output transistor. X is the module's byte address, and “1” means a fault is present. This readout is not supported by CPU 100 version 8MA01.

These bits are not additional physical digital inputs. Handle the output command and fault status separately in the PLC program. During troubleshooting, compare the program state, L+ supply and actual load response. Do not apply this S5-100U address description directly to other station types.

ET 200U address identifiers

The ET 200U manual specifies 048 for DP Siemens, 8DQ or 032 for DP Standard, and an address scope of one byte. The 8DQ configuration identifier does not mean the module has eight physical outputs. With station interfaces such as the IM 318-8MC12, use the table for the selected operating mode.

Switching limits and cabinet conditions

Maximum switching frequency is 100 Hz for resistive loads and 2 Hz for inductive loads. Maximum off-state residual current is 1 mA, so check the off-state response of low-current electronic loads. The S5-100U technical table specifies an ambient range of 0–60 °C for horizontal mounting and 0–40 °C for vertical mounting.

Similar models and spare selection

The 450-8MD11 is a different module for AC loads. The 451-8MA11 and 453-8MA11 differ in channel count and electrical ratings. Do not assume these models share the 450-8MB11's 24–60 V DC range.

The 451-8MR12 and 452-8MR11 use relay outputs, with different wiring and switching characteristics from transistor outputs. Do not match nearby codes such as the 450-8FA11 by appearance alone. Check the complete 6ES5 450-8MB11 code, load voltage, terminal base and address arrangement together. Disconnect system and load supplies before removal or installation.

Editor’s note

Pay close attention to the final letters when ordering. The 8MB11 and 8MD11 serve different loads: DC and AC respectively. Keep a clear photograph of the original label to make spare selection easier.

A 60 V marking on the module does not make 60 V suitable for a 24 V coil. The card switches the supply you connect to it. Read the load label first, then select the supply; that small check helps protect both the coil and the card.

If the red F indicator lights up, check L+ and the load wiring before writing off the module. A missing load supply can make a healthy card look faulty. Start with the simple measurements.

The output can resume operation when a short circuit clears. Remember that a connected valve or relay may become energised again as the wiring is repaired. Restore the circuit under controlled conditions once the cause has been corrected.

Where practical, have all four outputs checked with suitable loads, together with the F indicator and fault reporting. Agree whether the terminal base is included. Keep photographs of the label and wiring for the day the spare needs to be fitted.

OtomasyonAVM resources and PDFs

+ Siemens S5 PDF archive: our general documentation page. Detailed tables for this model appear in the S5-100U and ET 200U manuals below.

+ S5 digital output modules · S5 90/110 modules · S5 cable types

Related topics

+ 450-8MD11 · 451-8MA11 · 453-8MA11: load types and channel characteristics.

+ 451-8MR12 · 452-8MR11 · IM 318-8MC12 · PLC troubleshooting

Browse SIMATIC S5

S5 digital output modules · Small S5 modules · Siemens S5 PLC · Used Siemens equipment

Siemens and external references

+ Siemens S5-100U System Manual – English, 6ES5 998-0UB23: technical table and wiring diagram, printed p. 14-29 / PDF 379; program-based fault reporting, p. 6-6 / PDF 108.

+ Siemens ET 200U Distributed I/O Station – English: 450-8MB11 technical table, printed p. 8-30 / PDF 254; address identifiers, pp. 4-10 and 5-10 / PDF 79 and 118.

+ Siemens S5-90U/S5-95U System Manual – English: module technical table, printed p. 15-27 / PDF 391.