What is axis control?

Axis control manages a machine's controlled motion: where it goes, how fast it travels and how it gets there. The X slide of a cutting machine, its vertical Z head and an indexing rotary table are examples of motion axes. The objective extends beyond making a motor turn: the moving machine part must follow the required command.
What belongs to an axis?
A motion controller plans the move. The servo drive controls electrical power to the motor. The motor and transmission move the load, while an encoder or another suitable measuring system reports actual motion. The gearbox, screw and load are therefore part of the axis behaviour, not incidental hardware. Selecting a servo system requires more than matching power ratings.
A linear axis commonly uses millimetres and millimetres per second. A rotary axis may use degrees or revolutions. Axis control is not limited to servos; suitable stepper systems can also control machine axes. A servo axis uses feedback to correct differences between commanded and measured motion.
Turning motor revolutions into machine coordinates
Consider a screw with a 5 mm lead driven through a 2:1 mechanical reduction: two motor revolutions produce one screw revolution. Moving the carriage 100 mm requires 20 screw revolutions, or 40 motor revolutions. At 600 motor rpm, the ideal carriage speed is (600 ÷ 60 ÷ 2) × 5 = 25 mm/s, excluding acceleration, deceleration and mechanical losses.
The controller needs the correct units, transmission ratio, screw lead and direction. Otherwise, a displayed value of “100 mm” may not represent 100 mm of physical travel. Electronic gearing and coordinate scaling must be checked against the particular device's command and feedback units.
Different commands create different moves
In position control, an absolute move targets a coordinate; a relative move adds a displacement to the current position. From a starting position of 60 mm, “go to 200 mm” produces 140 mm of travel. “Move another 200 mm” produces a destination of 260 mm. The number alone is not enough to describe the instruction.
Velocity and torque modes regulate other quantities: velocity sets the rate of motion, while torque control regulates the motor's turning effort. A positioning move still needs velocity, acceleration, deceleration and jerk limits. Jerk is the rate of change of acceleration. An appropriate S-curve profile can soften motion, but cannot remove mechanical looseness.
Why simultaneous starts do not guarantee a straight line
Suppose an X–Y table must move from (0, 0) to (100, 50) mm. Command both axes independently at 50 mm/s and Y finishes after one second, while X takes two. In this ideal constant-speed example, the table first travels diagonally and then continues horizontally. The final coordinate can be correct while the path is wrong.
With linear interpolation, both axes follow a shared progression along the path. For this example's constant-speed section, X at 50 mm/s and Y at 25 mm/s preserve the straight line. A real trajectory planner coordinates acceleration and deceleration too. Matching the start and finish times alone does not establish the shape of the path between them.
The drawing illustrates ideal paths and omits acceleration and deceleration. The static lines remain available when motion is disabled.
Multi-axis coordination also covers relationships other than straight-line travel. A feed roller may follow another axis at a defined ratio; a robot must translate the tool path into joint-axis movement. An EtherCAT motion network can provide the timing infrastructure, but connecting the drives does not itself create a coordinated-motion algorithm.
How the PLC addresses an axis
Many platforms using the PLCopen approach provide MC_Power for enabling an axis, MC_Home for referencing, MC_MoveAbsolute for an absolute destination and MC_MoveRelative for a relative displacement. Availability and detailed behaviour depend on the controller's motion library. Adding a block does not replace the necessary drive and controller configuration.
The program must also handle the command's outcome. Busy indicates processing, Done indicates completion and Error reports a fault. CommandAborted can identify a move interrupted before completion. The next machine action should respect the library's completion conditions and the application's position tolerance.
What to verify on the machine
Reference and measurement: Check how the home reference relates to machine coordinates. An incremental encoder may need startup referencing. An absolute encoder does not automatically establish the correct machine zero. Motor feedback measures load position indirectly; significant backlash or compliance may call for a linear measuring system on the load.
Travel boundaries and monitoring: Software travel limits, limit switches, following-error monitoring and the target-position window serve different purposes. Following error is the difference between the instantaneous commanded position and measured position. Excessive error can result from incorrect scaling, insufficient torque or mechanical binding as well as unsuitable gains.
Tuning and acceptance: Assess autotuning and loop gains with the actual load. The highest gain is not necessarily the best setting. Check target arrival, settling time and repeatability together.
Technical references: Beckhoff — MC_MoveAbsolute · Beckhoff — MC_Home · CODESYS — Coordinated linear motion · PLCopen — Coordinated motion · Beckhoff — Axis monitoring