6ES5 375-0LA11

Siemens SIMATIC S5 6ES5 375-0LA11 8 KB EPROM Memory Submodule

The Siemens 6ES5 375-0LA11 is an 8 KB (1 × 8 KB) EPROM for storing programs or configuration data in SIMATIC S5 equipment. The 375-series submodule appears in the S5-101U hardware list and in Siemens compatibility tables for the CP 521 SI and CP 521 BASIC. Its EPROM programmer setting is 11 / BYTE.

This UV-erasable EPROM retains its contents without power. The 375-0LA15 is also listed as 8 KB with the 11 / BYTE setting. Check the label and the programmer you intend to use when choosing between the two. The Siemens PG 615 manual documents the jumper difference.

S5-101U hardware

The 1987 S5-101U hardware list identifies the 0LA11 as a 375 EPROM. It also lists the 101-8UA33 central unit and the 101-8UC11 and 101-8UC31 expansion units. Check the central unit’s program size limit separately from the submodule’s 8 KB physical capacity. The Siemens manual explains that the S5-101U copies the program into internal RAM and runs it from there.

What the CP 521 SI and BASIC store

Among the S5 communications processors, the CP 521 SI uses EPROM for message texts and parameter data. The CP 521 BASIC stores a BASIC program or initialization parameters. Both manuals list the 0LA11 as 1 × 8 KB, the 375-0LA21 as 2 × 8 KB and the 375-0LA41 as 2 × 16 KB.

The CP 521 BASIC manual lists the 375-0LC41 EEPROM and 375-0LD11 RAM as separate memory types. Match the memory type and stored contents as well as the capacity when choosing a spare.

PG 615 and the 0LA15 jumper configuration

The note under Table 2.9 in the PG 615 manual states that removing jumper 2 and fitting jumper 3 allows the 0LA11 to be handled as a 0LA15 on the PG. Siemens also specifies relabeling the converted submodule. This applies to the hardware configuration described in the PG 615 manual.

Verify 11 / BYTE on a compatible S5 programming device for the 0LA11. The 8 KB CMOS 375-1LA15 uses 411, and the 16 KB CMOS 375-1LA21 uses 412. Use the module socket to read the EPROM and the S5 PG cable and connection to back up a running CPU online.

Editor’s note

Photograph the 375-0LA11 label before ordering a spare. Record the jumper configuration if the submodule has previously been converted to the 0LA15 arrangement.

Record the full CPU or CP order number and the socket the submodule occupies. Isolate the equipment supply before removing or fitting it.

Before UV erasure, read the EPROM contents into a separate file. Keep any backup from the running CPU in a separate file as well.

If a CP is missing display or printer text, confirm which machine the submodule came from. Compare the message text and parameter files with that machine’s backup.

For a used unit, ask for a read test with 11 / BYTE. Run a blank check before reprogramming and compare the programmed module with the source file afterward.

OtomasyonAVM resources and PDFs

+ SIMATIC S5 memory submodules · Siemens SIMATIC S5 PLC overview

+ SIMATIC S5 PDF archive and system manuals

Related topics

+ 6ES5 375-0LA15 8 KB EPROM · 6ES5 375-1LA15 8 KB CMOS EPROM · 6ES5 375-0LA21 16 KB EPROM

S5 navigation

+ S5 memory cards · SIMATIC S5 · Siemens S5 PLC

External references

+ Siemens CP 521 SI manual · Table 2-2b, 8 KB and programming number

+ Siemens CP 521 BASIC manual · Table 2-3, compatible EPROMs

+ Siemens PG 615 manual · 0LA11 and 0LA15 jumper configuration (DE)

+ S5-101U hardware list · 375-0LA11 and central units (ES)

+ Siemens S5-101U operating instructions · Loading a program from a memory submodule

+ IBHsoftec EPROMMER table · 11 / BYTE setting (DE)