6ES5 410-7FA11

Siemens 6ES5 410-7FA11 — S5-110F 8-Channel 24 V DC Digital Output Module

The Siemens 6ES5 410-7FA11 is an 8-channel, 24 V DC digital output module for SIMATIC S5-110F. It belongs to the earlier digital output module range within the SIMATIC S5 family. Retain the complete 7FA11 suffix when selecting a spare.

The Siemens front panel examined shows 24 V DC and 1.8 A, while the side-label photograph reads “Digitalausgabe 8×A/24V=/2A”. Do not treat these markings as one verified operating limit. Confirm the applicable load rating against the installed hardware version and S5-110F documentation.

Output current and load selection

Do not round the front-panel 1.8 A marking up to 2 A. For the current calculation, assess individual channel loads and simultaneous operation separately. Eight channels alone do not establish a total board current rating.

Check pickup current for relays, contactor coils and other loads. Select any interposing relay and socket in the context of the existing S5-110F circuit and feedback arrangement. Do not choose a fuse rating solely from the 2 A side-label marking.

Suitability for the S5-110F system

Some S5 90/110 modules have similar housings. However, the S5-110F is a separate system within Siemens’ safety logic controller history. Assess a replacement against the full code and the documentation for the installed system.

Compare the mounting arrangement and mechanical connections, hardware version and installation drawings. A lit output LED does not establish that all machine safety functions have been verified. Complete the installation’s maintenance and functional-check procedure after replacement.

Connections and address checks

Label cables and connections before removal. Trace the load supply, common return and cabinet grounding against the existing drawing. An exact wiring manual for this model could not be verified, so pin numbers, galvanic isolation and short-circuit protection specifications are not stated here.

Match output addresses in the PLC program with the installed location and circuit drawings. During troubleshooting, examine the program command, supply and load circuit separately. Do not transfer terminal numbers or address settings from another S5 model.

Differences from similar order numbers

The 410-7AA11 and 410-7FA11 are different order numbers. The 410-0AA41 is another separate model. Do not transfer channel, current or connection specifications between these boards based only on the 410 designation.

The 415-7AA31, 415-7AB11, 415-7AB21 and 417-7AA21 pages allow comparison with other output options. These links do not establish direct interchangeability or S5-110F compatibility.

Editor’s note

Keep that small F in the order number in view when looking for a spare. Compare the complete label rather than assuming that another 410 board with a similar housing will do.

The 1.8 A front marking and 2 A side marking deserve a careful check. Match the hardware version to the system documentation before increasing a load. Establish the limit first, then connect the load.

If one output fails to operate, let us check the supply, terminals, cable and coil in sequence before condemning the board. Fitting a spare without finding a load fault may bring the same problem back.

Photograph the label and connections before removal, and back up the program. Switch off power and follow the installation’s replacement instructions. Recording the original arrangement now is easier than relying on memory later.

For a used digital output board, ask what testing has covered all eight channels. Look beyond the LEDs, and distinguish a suitable load test from the functional checks required in the S5-110F system.

OtomasyonAVM resources and PDFs

+ About Siemens S5 PLCs · S5-115U PDF archive. S5-115U documents must not replace the wiring manual for this S5-110F model. The Siemens document below covers system history; it is not the complete 410-7FA11 operating manual.

Related topics

+ 410-7AA11 · 410-0AA41 · 415-7AA31 · 415-7AB11 · 417-7AA21

Browse SIMATIC S5

+ S5 digital output modules · SIMATIC S5 · S5 90/110 modules · Used digital I/O modules · Siemens second-hand equipment

Siemens and external references

+ Siemens manufacturer front panel — channels 0–7, 24 V DC and 1.8 A marking (reference-unit photograph)

+ Siemens side-label photograph — S5-110F, exact 410-7FA11 code and 8×A/24V=/2A marking

+ Siemens Safety Integrated Application Manual, 4th edition — printed p.2: S5-110F system history (English, archived copy; not this module’s wiring manual)