6ES5 451-8MR12
Siemens 6ES5 451-8MR12 — 8-Channel Relay Output Module
6ES5 451-8MR12 is an eight-channel, galvanically isolated relay output module for the Siemens SIMATIC S5 family. It transfers digital output commands to field circuits through mechanical relay contacts. Siemens identifies the load class as 30 V DC / 230 V AC; the relays also require a separate 24 V DC supply.
Siemens lists the module for S5-90U, S5-95U, S5-100U, ET 100U and ET 200U. Check the connection hardware in the installed SIMATIC S5 arrangement. Within the ET 200 family, this compatibility specifically concerns ET 200U; check the interface and station type together. The outputs form four isolated groups of two.
Relay supply and contact ratings
The external relay supply is 24 V DC nominal, with a 20–30 V DC operating range. When checking the S5 power supply and field wiring, distinguish the relay operating supply from the voltage switched by its contacts. An output command cannot energize a relay without the external supply.
The S5-100U manual specifies contact switching limits of 3 A at 250 V AC or 1.5 A at 30 V DC for resistive loads. For inductive loads, the limit is 0.5 A at 250 V AC or 0.5 A at 30 V DC. Select relays, contactors and interposing relay coils using the applicable load rating; the 3 A continuous-current figure does not permit switching every load at 3 A.
Front connector options
This module requires a separate front connector. The manual lists the 40-pole screw-terminal 6ES5 490-8MB11 and 20-pole screw-terminal 6ES5 490-8MB21. Check the wiring against the arrangement of the connector actually fitted.
The 40-pole crimp versions are 490-8MA13 with contacts and 490-8MA03 without contacts. Preserve the diagram’s A/B terminal rows; terminal numbers alone are insufficient when transferring wires. The common connections within each pair must not be treated as eight independently isolated contact groups.
LED indication and protection
The red F LED indicates a missing L+/M relay supply. It does not diagnose every fault in the load wiring. For fault diagnosis, check the PLC program command, relay operation and switching of the actual load separately.
Each contact is bridged by a varistor. Siemens ST 50 states that this can produce a maximum residual current of 1 mA at 250 V AC. There is no electronic short-circuit protection. Assess applications needing an SSR or a fast electronic output separately; the specified 10 Hz maximum switching frequency does not imply unlimited contact life. Establish safe machine conditions before testing.
Comparing similar order codes
451-8MA11 has DC electronic outputs, 451-8MD11 has AC electronic outputs, and 452-8MR11 is a four-channel relay output module. When comparing 451-8MR11 or 453-8MA11, also check the complete code, output technology and wiring arrangement. These links are comparison references, not a list of direct replacements.
Editor’s note
Start with the 24 V DC relay supply. A contact switching a 230 V load does not mean the relay operating supply should be 230 V. Keep the two sides clear before connecting anything.
Do not connect a load just because its current seems to match the label. A heater and a contactor coil behave differently. Allowing for the 0.5 A inductive-load limit helps protect a healthy card.
A relay click is useful, but it is not the whole test. For a used card, test all eight channels individually with suitable loads; worn contacts can still sound perfectly normal.
Photograph the wiring before changing the front connector. Take time to match the 20- or 40-pole arrangement, A/B rows and common terminals. One hurried connection can turn into a long fault-finding job.
If the red F lamp comes on, check the L+/M supply before setting the card aside. If a load fails to release, also assess the coil, field wiring and possible residual current through the varistor.
OtomasyonAVM resources and PDF files
+ S5 PDF files and user manuals · Siemens ET200 manuals · About Siemens S5 PLCs. The main reference is the S5-100U System Manual, EWA 4NEB 812 6120-02b, printed page 14-34 / PDF page 384. The document is in English.
Related topics
+ 452-8MR11 relay output · 451-8MA11 DC output · 451-8MD11 AC output · 490-8MB11 front connector · 490-8MB21 front connector.
Browse SIMATIC S5
+ S5 digital output modules · S5 cables and connections · S5 interface modules · Siemens S5 PLC · Siemens second-hand equipment.