6ES5 463-4UA11

Siemens 6ES5 463-4UA11 – 4-Channel Isolated Analog Input Module

6ES5 463-4UA11 is a four-channel, galvanically isolated analog input module in the Siemens SIMATIC S5 U-periphery range, used with systems such as the S5-135U, S5-150U and S5-155U. Within the S5 analog module range, it accepts 0–1 V, 0–10 V, 0–20 mA and 4–20 mA signals. The 4UA11 version has a 20 ms integration time and four-channel measurement cycle at 50 Hz.

The module transfers continuous readings from pressure sensors and other transmitters with suitable outputs to the PLC program. During commissioning, match the 0–10 V or 4–20 mA signal type, front connector wiring and program scaling.

Selecting the input range

For analog voltage measurement, use the 0–1 V or 0–10 V connection. Input impedance is 90 kΩ for 0–10 V output sensors and greater than 10 MΩ on the 1 V range. Select each range through the appropriate front connector terminals and jumpers.

For analog current measurement, input resistance is 50 Ω on 0–20 mA and 62.5 Ω on 4–20 mA. When connecting 4–20 mA analog sensors, distinguish between a two-wire transmitter powered by the module and a four-wire transmitter with a separate supply.

The resistors that determine the analog signal range are built into this module; it does not use the plug-in range submodules found on the 460/465 types. Check the terminals and range jumpers for each analog input against the wiring diagram on printed manual page 5-13.

Isolation and power connections

The four inputs are isolated from one another and from reference M. Maximum permissible potential difference is 25 V AC / 60 V DC. With a two-wire transmitter, however, the channel common is connected to L−, which removes isolation between that channel and the L+/L− supply. Account for this when reviewing grounding and common reference connections.

Digital section: 5 V ±5% from the system bus, typically 150 mA. Analog section: external 24 V DC, approximately 150 mA. Apply 24 V across F+/F− to enable bus access. Front connector terminals are 1 for F+, 2 for F−, 3 for L+ and 21 for L−.

Addressing and 4–20 mA scaling

Set the module start address on its address switch. Four channels occupy 8 bytes, with channel words at offsets +0, +2, +4 and +6. Compare the replacement module’s switch positions with the peripheral addresses used by the existing program.

When processing analog I/O data, use this module’s 11-bit two’s-complement representation with 1024 units across the nominal range. Individual channel switches select the 0–1023 or 256–1279 data format for 4–20 mA. These are the manual’s measurement units; scaling must also account for their bit positions in the raw input word.

The distinction between analog and digital inputs also matters during fault finding: a zero reading alone does not establish a broken wire. There is no general open-circuit diagnostic; on 4–20 mA loops, the program can evaluate current below 3 mA as an indication of a broken circuit. This helps separate a pressure transmitter fault from a valid low process reading.

Related versions and system checks

4UA11 is the 50 Hz version. 6ES5 463-4UA12 also belongs to the 20 ms/50 Hz group, while 6ES5 463-4UB12 belongs to the 16⅔ ms/60 Hz group. Check wiring and program requirements before treating a different suffix as a replacement.

6ES5 460-4UA11 has eight isolated inputs, while 6ES5 465-4UA11 is a different, non-isolated 16/8-input design. For a 463-4UA11 installation, check the four-channel requirement, front connector, rack, power supply and CPU together.

When purchasing a used analog module, request results for all four channels, a clear label photograph and confirmation that the front connector is included. Independently measure the output of any used analog sensor employed for testing; a sensor-only trial does not establish module accuracy.

Editor’s note

Start with the label. A 463 marking is only the beginning: confirm the full 4UA11 code. Photograph the old module’s label and switch settings before removal; it is a small step that saves a lot of guesswork later.

Give all four channels a fair test. One good reading does not establish that the whole module is sound. Apply low, middle and high reference signals with a calibrator and record each channel’s raw values.

Take your time with the jumpers. The front connector is part of the range selection. Record the existing wiring before disconnecting it, then compare current and voltage connections with the diagram.

If readings disappear, check the basics first. Measure the analog supply and the F+/F− enable voltage before condemning the module. With a two-wire transmitter, check the channel common connection as well.

If the field signal is right but the display is wrong, revisit scaling. Each 4–20 mA channel can have its own data format. Confirm that the switch setting and program agree before replacing hardware; a calm check here can save an unnecessary repair.

OtomasyonAVM resources and PDFs

+ About Siemens S5 PLCs – system and maintenance information

+ SIMATIC S5 analog input and output modules

+ Shared S5 PDF archive – manuals and files page

Related topics

+ Understanding 0–10 V and 4–20 mA signals

+ Grounding and common references

+ Analog input and output fundamentals

Browse SIMATIC S5

+ S5 analog modules

+ SIMATIC S5 system pages

+ Siemens S5 PLC main page

+ Used Siemens products and model pages

Siemens and external references

+ Siemens U Periphery, C79000-B8576-C300-06 – 463-4UA11 technical data, printed pages 5-11–5-13 (English)

+ Siemens U Periphery – 463 measured values and 4–20 mA formats, printed page 3-8 (English)

+ Siemens U Periphery – 463 operation and addressing, printed pages 1-8–1-10 (English)