6ES5 463-4UA12
Siemens 6ES5 463-4UA12 – 4-Channel Analog Input Module
6ES5 463-4UA12 is a four-channel analog input module in the Siemens SIMATIC S5 family, documented for S5-135U/155U systems. It measures 0–1 V, 0–10 V, 0–20 mA and 4–20 mA. The inputs are isolated from one another. This 50 Hz version has a specified measurement cycle of 20 ms.
The module brings measurements from pressure transmitters and other suitable analog sensors into the PLC. The analog signal, front connector wiring and software scaling must agree.
Selecting the measuring range
Each channel's range is selected by wiring and jumpers in the front connector. A 0–10 V sensor needs the voltage connection; a 4–20 mA sensor needs the appropriate current connection. Changing a software scaling constant alone does not reconfigure the input circuit.
For voltage measurements, input resistance is >10 MΩ at 1 V and 90 kΩ at 10 V. For current measurements, it is 50 Ω at 0–20 mA and 62.5 Ω at 4–20 mA. Confirm the transmitter's 0–10 V or 4–20 mA interface before wiring.
Power, enable signal and isolation
The digital section receives 5 V from the S5 bus; the analog section requires an external 24 V DC supply. The front connector also needs a 24 V enable signal at F+/F−. Check these separately when inspecting the S5 cables and connectors.
With a two-wire transmitter, the channel's common input must connect to L−, removing that channel's isolation from L+/L−. Before connecting a used analog sensor, identify whether it is a two-wire or four-wire device. Wiring arrangements should follow the actual analog measurement application.
Data format and addressing
The analog-to-digital conversion produces an 11-bit two's-complement representation. For 4–20 mA, channel switches select 0–1023 or 256–1279. The scaling in the PLC program must match each channel's selected format.
Each channel occupies one word, so four inputs require 8 byte addresses. During PLC troubleshooting, compare the raw word, channel address and displayed engineering value. Apply the appropriate checks for analog and digital inputs.
Comparing similar order numbers
6ES5 463-4UB12 is the 60 Hz version. 6ES5 465-4UA12 has a different channel and range arrangement and requires a separate replacement assessment. 6ES5 470-4UA12 is an analog output module. Confirm the input or output function against the complete order number.
When buying a used analog module, request a clear label photograph, confirmation that the front connector is included, and details of the channel tests performed. Choose from the S5 analog module range using the full specification.
Editor’s note
Take a moment before removing the old card. Photograph the jumpers and switch settings clearly. Keeping a record of the working setup makes the replacement much easier to check.
If a 4–20 mA transmitter's lower endpoint appears offset, leave its calibration alone initially. Compare the selected data format with the program's expected format first. Give a healthy sensor the benefit of a proper check.
If a fitted card produces no readings, check beyond the rack power indication. Measure the analog 24 V supply and F+/F− enable signal at the connector. A missing connection can otherwise lead to a long search.
With a two-wire transmitter, take care over the change in isolation caused by the common connection. Understand the purpose of an existing jumper before carrying it over to a replacement installation.
For a used card, one plausible reading on one channel is only a starting point. Have all four channels checked at low, middle and high points with a suitable calibrator. For 4–20 mA, use 4, 12 and 20 mA and assess the readings against the selected format.
Before adding a software correction for a persistent small error, inspect the range jumper, contacts and connection resistance. Resolve a connection problem at its source so the program remains understandable for the next person.
OtomasyonAVM resources and PDFs
Start with About Siemens S5 PLC and the S5 analog module directory for system and module information.
The OtomasyonAVM Siemens S5 PDF archive collects our available S5 documents. For this card's detailed specifications and wiring, use the English S5-135U/155U and U Periphery manuals linked below.
Related topics
+ 6ES5 463-4UA11: earlier 50 Hz version; check the full order number and settings when replacing.
+ 6ES5 463-4UB12: the 60 Hz version and frequency distinction.
+ 6ES5 465-4UA12: a different analog input arrangement.
+ 6ES5 470-4UA12: the analog output function.
Browse SIMATIC S5
S5 analog modules · SIMATIC S5 systems · Siemens S5 PLC · Used Siemens equipment
Siemens and external references
+ Siemens S5-135U/155U System Manual – C79000-G8576-C199-07, English: pp. 9-2, 9-39 and 9-47–9-49; order numbers, addressing, specifications and Figure 9-17 wiring diagram.
+ Siemens U Periphery – 6ES5 998-0PC22, English: analog input section §5.3; 463-4UA11/4UA12 and 4UB11/4UB12 specifications, data format and transmitter connections.