6ES5 950-8MD11

Siemens 6ES5 950-8MD11 PS 950 Power Supply

The Siemens 6ES5 950-8MD11 is a rail-mounted PS 950 power supply for 24 V DC circuits in S5-100U and ET 100U installations in the SIMATIC S5 family. Its input is selectable between 115 and 230 V AC. The 24 V DC output delivers up to 10 A at ambient temperatures up to 50 °C when mounted horizontally.

In an S5-100U cabinet, the PS 950 can supply the CPU’s 24 V input or the field loads, depending on the wiring. Trace the cabinet drawings to see which branch supplies sensors for digital inputs, loads on digital outputs and field devices on combined I/O modules. This distinction helps narrow down a fault when several field devices stop at once.

Input selection, terminals and output limits

Siemens specifies 93–127 V AC at the 115 V setting, 187–253 V AC at the 230 V setting and a frequency range of 47–63 Hz. Rated input current is 3.2 A and 1.7 A, respectively. Mains connects to L1, N and PE, and the DC output is on L+ and M. Isolate the mains and verify that the circuit is de-energized before checking the wiring and connectors, voltage selector and protective earth.

The 24 V output has a specified range of 22–26 V DC. For vertical installation, Siemens specifies 8 A maximum at ambient temperatures up to 60 °C. When comparing cabinet power supplies, read the current rating alongside the mounting orientation and ambient temperature. The PS 950 has galvanic isolation between its mains input and DC output.

Power distribution in S5-100U and ET 100U

In the S5 CPU range, the PS 950’s L+ and M output can feed the 24 V input of a CPU 100, CPU 102 or CPU 103 where the cabinet drawings call for it. The CPU has its own circuitry for the internal bus supply.

Check how the field wiring is terminated on 700-8MA11 screw-terminal or 700-8MA21 crimp-terminal bus units. If the fault is confined to the expansion side, check its power supply and S5 interface connection separately. On an ET 100U, trace the control supply to the 318-8 interface module separately from the field supply for sensors and actuators.

Siemens documents the 6ES5 930-8MD11 for the S5-100U CPU supply. The 6ES5 931-8MD11 is a lower-current 24 V option. Compare the function and load of the 24 V branch when choosing between these supplies and the PS 950.

LED indications, ENABLE and RESET

The green LED indicates that the 24 V output is present. Siemens identifies a flashing red LED as loss of ENABLE. A steady red LED indicates a latched shutdown after an overload or short circuit. Once the fault is cleared, RESET can restore the output.

Editor’s note

Ask for photos of the full 950-8MD11 nameplate and front terminals. Similar order numbers can have different output ratings and intended uses.

Before commissioning a spare from another cabinet, check the 115/230 V selector and input fuse against the manual. Access the selector only after isolating the mains.

If the red LED flashes, trace the ENABLE circuit on the cabinet drawings. If there is an external enable contact, check what conditions cause it to open.

With a steady red LED, check the 24 V load branches for an overload or short circuit before pressing RESET. Once the fault has been cleared, have the output checked under a suitable load.

For a used power supply, ask for a loaded 24 V reading and the ENABLE and RESET test results. Ask what load and mounting orientation were used for the test.

OtomasyonAVM resources and PDFs

+ SIMATIC S5 power supplies · Siemens S5 PLC overview

+ OtomasyonAVM shared SIMATIC S5 PDF archive

Related topics

+ 6ES5 930-8MD11 · S5-100U CPU supply.

+ 6ES5 931-8MD11 · 24 V power supply.

+ 6ES5 318-8MA12 · ET 100U interface module.

To offer a 950-8MD11 for sale, email a nameplate photo, quantity and test status to otomasyonavm@gmail.com.

Navigation

+ S5 power supplies · S5-100U and related CPUs · SIMATIC S5 · Used Siemens equipment

External references

+ Siemens S5-100U CPU 100/102/103 Manual (Russian PDF) · pp. 2-14–2-16, PS 950 drawing, ratings and LED diagnostics.

+ Siemens ET 100U Distributed I/O Manual (English PDF) · p. 3-67, control and load supply circuits.

+ 6ES5 950-8MD11 product listing · S5-100U and ET 100U applications.