6ES5 316-8MA12

Siemens 6ES5 316-8MA12 — IM 316 Expansion Interface Module

The Siemens 6ES5 316-8MA12 is an IM 316 expansion interface for connecting up to three additional module tiers in SIMATIC S5 systems. This S5 interface module extends the local I/O bus across separate mounting tiers, allowing four tiers including the main tier.

The manufacturer's data sheet covers S5-100U, ET 100U and ET 200U systems. In ET 100U installations, the 318-8MA12 station interface and IM 316 perform different tasks. In ET 200U stations within the ET 200 family, the IM 316 likewise extends the station's local module tiers.

Tier arrangement and bus connection

Use one IM 316 on each interconnected tier. Its ribbon cable connects to the last bus unit on that tier. With bases such as the 700-8MA11 screw-terminal bus unit or 700-8MA22 crimp bus unit, check that the ribbon connection is fully seated.

The S5-100U and ET 100U manuals specify a maximum of 16 bus units in total. Adding tiers does not increase the total module or address capacity supported by the SIMATIC S5 central unit.

IN/OUT connection and cable options

Connect the preceding tier's OUT socket to the next tier's IN socket. Siemens lists the 6ES5 712-8AF00 — 0.5 m and 6ES5 712-8BC50 — 2.5 m connecting cables.

The same list includes 6ES5 712-8BF00 — 5 m and 6ES5 712-8CB00 — 10 m. Check the full order number and routing when selecting an S5 connecting cable. Secure both retaining screws on each connector; they provide mechanical retention and shield contact.

Supply and main specifications

The IM 316 draws typically 27 mA from the +9 V system supply and is rated to pass up to 2.5 A to the expansion unit. Do not confuse this rating with the module's own consumption or field-output load capacity. Include all modules in the S5 power-supply calculation; for S5-100U, review system supply options such as the PS 935 according to the installation.

Dimensions are 45.4 × 135 × 39 mm (width × height × depth), with an approximate weight of 120 g. The manual specifies a permissible potential difference of ±1 V between the IM 316 and the central grounding point.

Mounting rails in separate cabinets require a common reference potential. Review grounding and equipotential bonding together with bus-cable installation to maintain noise immunity.

Difference from the IM 315 and module selection

The 6ES5 315-8MA11 — IM 315 consists of two parts permanently joined by a 0.5 m cable for a two-tier arrangement. The IM 316 uses separate 712-8 cables for multi-tier configurations. Match a replacement to the existing tier and cable arrangement.

Check addressing and supply requirements separately for the digital input, digital output and analog modules on the expansion tiers. The IM 316 is not a signal module that adds input or output channels itself.

Installation and fault finding

Change the module with system power switched off. During PLC debugging, if an entire tier is unavailable, inspect the IM 316, IN/OUT cable, ribbon connection and bus supply together. For S5-100U cabinet mounting, the manual specifies at least 210 mm between mounting rails.

Editor's note

Start by following the cable between the tiers with your own eyes. Confirming that it runs from OUT to IN gives you a sound starting point.

If every module on a tier disappears, give the shared connection a fair check before blaming all the cards. A single loose ribbon cable can affect the whole tier.

Keep both connector screws fitted. On a vibrating machine, a plug that merely stays in place is not enough; secure seating and shield contact matter over time.

Where possible, test a used module with a serviceable 712-8 cable and a working module tier. Record the equipment used, so the next check starts with useful evidence.

Before adding another tier, write down the addresses and total bus current. Compare the arrangement with the S5 system information; a clear record helps both you and the next person maintaining the machine.

OtomasyonAVM resources and PDFs

+ Browse the OtomasyonAVM S5 PDF archive for system manuals. Relevant IM 316 sections are 3-5–3-7 and 14-15 in the S5-100U manual, and 2-13 and 3-8–3-11 in the ET 100U manual. The manuals below are in English.

Related topics

+ IM 315 — 6ES5 315-8MA11 · ET 100U — 6ES5 318-8MA12 · 712-8AF00 connecting cable · 712-8BC50 connecting cable.

+ 700-8MA11 bus unit · 700-8MA22 bus unit · 935-8ME11 power supply.

Browse SIMATIC S5

+ S5 interface modules · S5 cables and connectors · SIMATIC S5 systems.

+ Siemens S5 main page · Used Siemens automation equipment.

Siemens and external references

+ Siemens S5-100U System Manual — EWA 4NEB 812 6120-02b, English: tier connections, installation and the technical table for the exact order number.

+ Siemens ET 100U Manual — EWA 4NEB 812 6040-02a, English: IM 316 specifications, IN/OUT connections and tier arrangement.

+ Siemens 6ES5 316-8MA12 data sheet — 20 July 2020, archived German copy: identifies use with up to three expansion tiers in S5-100U, ET 100U and ET 200U systems.