6ES5 685-0UA11
Siemens 6ES5 685-0UA11 – PG 685 CRT Programming Unit, German Version
Siemens 6ES5 685-0UA11 is the German version of the PG 685 programming unit for SIMATIC S5. Its CRT screen and keyboard support program preparation, inspection and maintenance through suitable STEP 5 software. It belongs to the programming equipment used with Siemens S5 PLCs; it is not an input/output board installed in a SIMATIC S5 CPU rack.
A historical Siemens software notice distinguishes 685-0U.11 as PG 685 I from 685-0U.12 as PG 685 II. Processor, memory and disk specifications from another PG 685 must therefore not be assigned automatically to this order number. When reviewing the Siemens S5 system, distinguish the controller's operating role from the programmer's maintenance role.
STEP 5 programming and testing
The period STEP 5 environment for the PG 685 includes KOP, FUP and AWL representations and data block functions. These correspond to ladder diagram, function block diagram and statement list for PLC programming. Available testing and transfer functions must be assessed against the installed package, software release and connected CPU.
When reviewing S5-90U, S5-90U–115U CPU groups and S5 module families, the PG 685 name alone does not establish compatibility. Check the target CPU's complete order number, required software and connection arrangement. Also compare the project stored on the programmer with the version actually running in the CPU.
Operating system, floppy disks and hard disk
Period Siemens documentation identifies PCP/M-86 and S5-DOS operation for the PG 685. These environments are distinct from modern Windows/STEP 7 installations. Record the system disks, installed STEP 5 packages and actual boot behaviour together.
The PG 685 uses floppy and hard disk storage. This page does not assume that every surviving unit has the same disk capacity or hardware configuration. Its project storage and the CPU's S5 memory modules are different media; possession of one does not establish that a backup of the other exists.
For archives exchanged with other period programmers such as the PG 635 and PG 675, check disk format and software version. A disk physically fitting a drive does not establish that it can be read or safely rewritten. Back up a unique archive using an appropriate method before attempting conversion or repair.
PLC connection and communication software
Evaluate the S5 cable and connector, target PLC programming port and programmer interface together. For example, the PG 7.. designation on the 6ES5 734-2BD20 cable page does not establish direct PG 685 compatibility. Select cables using the manufacturer's pin assignment and electrical interface requirements rather than connector appearance.
S5 interface modules and S5 communication modules may require dedicated packages in addition to basic STEP 5. The Siemens CP 530 manual explicitly documents COM 530 for S5-DOS on the PG 685. This example does not imply that the same software configures every communications processor; use the package specified for the particular CP.
Where installations include equipment such as the 6ES5 757-0AA11 PG-MUX, document the device, cabling and selection arrangement separately. The presence of a multiplexer or converter does not automatically resolve every interface difference between the programmer and target PLC.
Similar order numbers and supplied equipment
6ES5 685-0UA11 identifies the complete PG 685 programming unit. The 6ES5 685-1AA11 graphics module and 6ES5 685-3AA11 upgrade item have different order numbers and purposes. When selecting S5 additional equipment or used Siemens equipment, establish whether an offer covers a complete programmer, a spare board or a software/upgrade item.
Editor's note
A visible screen is only the beginning of a useful condition check. Confirm that STEP 5 starts, every keyboard key works, a project file opens and communication succeeds with a suitable test CPU. During PLC troubleshooting, distinguish connection failures from program faults.
Protect any unique factory disk before doing anything else. Formatting in the hope of fixing a problem can destroy the archive that makes the programmer valuable. Obtain a readable copy or suitable disk image first, then perform experiments on a copy.
A CONFIGURATION message at startup does not by itself prove hard disk failure. The PG 685 short guide describes checking the hardware configuration with a test disk. Establish the installed hardware and available backups before changing configuration or formatting storage.
Inspect CRT text sharpness, image stability and behaviour after warming up. A unit that starts cold may lose its display later. Internal CRT and power supply inspection should be performed by a technician familiar with this equipment; unplugging does not establish that all stored electrical energy has dissipated.
Confirm in writing whether the delivery includes system and test disks, software version information, a suitable connection cable and readable project backups. A working programmer does not establish that the old machine's comment and symbol files are included.
Check source and destination twice before transferring a program to a PLC. An old project can overwrite a running CPU quickly, while recovering the latest changes may be difficult. Preserve the existing state before making controlled changes.
OtomasyonAVM resources and PDFs
Start with About Siemens S5 PLC, S5 cables and S5 memory modules.
+ S5-115U PDF files: an archive of related CPU and system documentation; it does not replace the PG 685 hardware manual.
Related topics
+ 6ES5 635-0UA11 – PG 635: a different programmer from the same period.
+ 6ES5 675-0UA11 – PG 675: check its hardware and archive requirements separately.
+ 6ES5 685-1AA11: PG 685 graphics module.
+ 6ES5 685-3AA11: a separate PG 685 upgrade order item.
Browse related equipment
Siemens S5 PLC · S5 CPU family · S5 additional equipment · Cables · Communication modules · Used Siemens equipment
Siemens and external references
+ Siemens PG-685 Kurzbeschreibung: third-party copy of the Siemens training centre's draft short guide dated 27 November 1986; configuration, system environment and STEP 5 functions.
+ Siemens SINEC L1 / CP 530 manual: the “COM 530 with S5-DOS” section documents PG 685 software use.
+ Siemens SiePortal – historical software notices: notice 4174355, listed under a different PG 685 II order number, distinguishes the PG 685 I (.11) and PG 685 II (.12) families. This link is not the datasheet for the unit described here.