6ES5 685-1AA11
Siemens 6ES5 685-1AA11 — PG 685 Monochrome Graphics Module
Siemens 6ES5 685-1AA11 is identified in product records as a monochrome graphics module for the PG 685 programming device. It is a spare part associated with the display hardware of the PG 685 used for SIMATIC S5 work. Match the complete order number, physical board arrangement and programmer hardware version before selection.
Its maintenance role concerns the graphics display section of a legacy programming device. If a PLC programming workstation loses or corrupts its image, assess the display hardware, screen, power and software environment together. A visible defect alone does not identify this board as the failed component.
Matching the device and board
Treat this order number as a PG 685 graphics spare. Its listing among S5 accessories does not establish compatibility with a PLC rack slot. When buying a PLC accessory, compare the label, connections and any revision marking. Establish interface compatibility from the hardware documentation rather than connector appearance alone.
Graphics and software checks
Start with the programmer’s existing, known working software arrangement. If the project uses ladder/KOP, FBD/FUP or an instruction list/AWL, check that these views open in the relevant software. This is a separate step from testing the board’s monochrome graphics function with the actual graphics application.
A change of PLC programming language or project file can change what appears on screen. Compare the same application, project and screen settings before attributing the difference to hardware. Changing the software setup during a board replacement makes the result harder to interpret.
A practical display fault check
During troubleshooting, observe the startup display, application text and graphics screen separately. Record the point at which a programmer used with a Siemens S5 system loses its image. This helps distinguish a graphics-related symptom from a wider device problem.
Back up program and system files before testing. Keep the PG 685 S5-DOS basic software package and existing installation information documented separately from the board. Replacing a graphics module does not by itself call for reinstalling the programming software or formatting the disk.
Separate communication checks from display checks
Where practical, test the display before performing any PLC write operation. Inspect the PLC connection cable and S5 cable arrangement separately. A communication error occurring alongside an image defect does not establish a common failed component.
Other legacy programmers
The PG 635 and PG 675 belong to the same broad generation of programmers, but that does not establish interchangeable graphics boards. Match 6ES5 685-1AA11 to the actual PG 685 model, board identification and hardware arrangement. Use the relevant device documentation for electrical ratings and pin assignments.
Editor’s Note
For a used Siemens graphics board, ask for readable identification, photographs of both sides and close views of the connections. Compare any PCB and revision markings with the original board as well as the order number.
Look for corrosion, liquid marks, discoloured areas and poor rework. A clean appearance does not establish operation. Ask which programmer and application were used for the test.
Disconnect the programmer from power before removing or fitting the board. Have work around an older CRT display and power section performed according to the service procedure. Do not force a connector that does not seat correctly.
A startup photograph is only part of a useful test. Check the text screen and the graphics application, then observe the image after the device has run for a while. Record any S5 PLC communication test separately from display testing.
Protect the working programmer’s disk, files and settings. Do not put the only copy of an old project archive at risk during a display repair. Back up first, change one thing at a time and repeat the same test conditions.
OtomasyonAVM resources and PDFs
Browse the PG 685 programmer, S5-DOS basic software package and S5 accessories pages for the related equipment group.
Shared SIMATIC S5 PDF archive — System documentation and programming resources. The Siemens WF 470 document below is a general reference to PG 685 graphics mode, not a board-specific installation manual for 6ES5 685-1AA11.
Related topics
+ 6ES5 885-0SA11 S5-DOS basic package
Browse SIMATIC S5
+ Siemens second-hand equipment
Siemens and external references
+ Siemens — Equipment for Special Machines, PG 685 graphics-mode reference, English
+ Allmendinger — 6ES5685-1AA11 product identification, German