6ES5 454-7LA11

Siemens 6ES5 454-7LA11 – 16-Channel Digital Output Module, 24 V DC / 2 A

The 6ES5 454-7LA11 is a 16-channel, 24 V DC transistor output module for the S5-115 series in the SIMATIC S5 family. Part of the S5 digital output range, it transfers CPU commands to DC field loads. Rated channel current is 2 A; optocoupler isolation is provided in four groups of four outputs.

Nominal load voltage is 24 V DC, with a permissible operating range of 20–30 V DC. Size the power supply for the actual field load and consider rack power alongside the output load supply. Siemens specifies an on-state output voltage of at least L+ − 3 V.

Total current limit per group

Siemens limits each four-channel group's total output current to 50% of the sum of its rated currents. This gives 4 × 2 A × 50% = a maximum of 4 A per group. A 2 A channel rating does not permit all four channels in the same group to carry 2 A simultaneously. Size cables and group supply connections accordingly, and check grounding and M references.

Output connection and protection

Connect the load between the output terminal and M. The module has electronic short-circuit protection, but still requires suitable loads and external circuit protection. For an interface relay, check coil current and suppression; select fusing with regard to the supply circuit and wiring. Do not parallel outputs to increase current capacity.

Maximum switching frequency is 100 Hz for resistive loads and 0.27 Hz for inductive loads. Do not apply the resistive-load switching rate to coils. Check load inrush and operating frequency separately.

Front connector and existing wiring

The 490 range includes the 24-pole screw-terminal 490-7LB11, 46-pole screw-terminal 490-7LB21 and 46-pole crimp 490-7LA11. Match the installed connector's code, pole count and wiring to the exact 7LA11 diagram. Do not select a connector or prepared wiring assembly solely by the 454 family name.

Addressing and channel testing

The 16 outputs occupy two output bytes. Check PLC program addresses against the actual rack and slot arrangement. During testing, confirm the output command, real load response and any digital input feedback together. During troubleshooting, distinguish an individual channel fault from a shared supply problem or excessive group load.

Comparison with the 7LA12 and other modules

The 454-7LA12 and 454-7LB11 are separate ordering codes. Do not treat them as automatic replacements without checking the 7LA11 specifications, grouping and front connections. Other S5 outputs such as the 451-7LA12 also differ in channel count and current rating.

The 457-7LA11 is a low-current open-collector output, while the 458-7LA11 uses a different output technology. Check the complete code, load type, group current and wiring arrangement when selecting a spare. Disconnect system and load supplies before removing the module or front connector.

Editor’s note

Start with the group load on this card. A 2 A marking does not mean all four outputs in one group can each carry 2 A at once. The group's combined limit is 4 A. Distributing loads correctly at the start is easier than chasing overheating and interruptions later.

Not every 24 V coil is the same load. Check the continuous current and inrush of the relay, contactor or valve. For frequently operated coils, pay particular attention to the module's inductive-load switching rate.

Electronic protection is no reason to test the card with a short circuit. Check the field cable, coil and suppression component first. A replacement card alone will not fix the fault that damaged the original.

Keep the final digit in 7LA11 and 7LA12 in mind. Compare label and front-connection photographs and check the terminal arrangement against the drawing. One careful wiring check is easier than moving cables by appearance and troubleshooting afterwards.

Where practical, assess a used card under suitable load with all 16 channels tested. An illuminated indicator without a load is not enough. Ask whether the front connector is included, and keep the original card labelled until the replacement setup is verified.

OtomasyonAVM resources and PDFs

+ Siemens S5 PDF archive: our documentation page.

+ S5-115H System Manual – English, p. 17-27 / PDF page 459: the manual on our website contains the exact 6ES5 454-7LA11 technical table and connection diagram.

Related topics

+ 454-7LA12 · 454-7LB11 · 451-7LA12: channel, grouping and load comparisons.

+ 490-7LB11 · 490-7LB21 · 490-7LA11: comparison of front connector types.

Browse SIMATIC S5

S5 digital output modules · S5 racks · Siemens S5 PLC · Used Siemens equipment

Siemens and external references

+ Siemens S5-115H Manual – English, EWA 4NEB 811 6111-02b, p. 17-27: exact 7LA11 code; 16 outputs, 24 V DC, 2 A, isolation in groups of four, 50% group-current limit, electronic protection and switching rates. Front connector codes are listed on p. 17-61.

+ Siemens 454-7LA11 technical page – English, one page: third-party archive copy of p. 17-27 from the same Siemens manual.