6ES5 301-5CA12
Siemens 6ES5 301-5CA12 – IM 301-5 Central Controller Interface Module
Siemens 6ES5 301-5CA12 is an IM 301-5 interface module installed in the central controller of a SIMATIC S5-135U/155U system. Part of the S5 interface module range, its lower front connection supports up to 200 m total distributed expansion through a 721 cable and the remote unit’s 6ES5 310-3AB11 / IM 310.
The upper front connection serves centralized EG 184U and EG 187U units without their own power supplies. The manufacturer’s system manual pairs this connection with IM 312-5CA11 / IM 312-5CA21 interfaces and their attached 0.5 m / 1.5 m cables. The upper and lower connections have different distance limits.
Distributed connection: IM 310 and 200 m
One IM 301 supports up to four remote expansion units. The 200 m limit applies to the total 721 cable length from the controller to the last unit. Include every intermediate section when assessing S5 cables and connectors.
The remote EG 183U expansion unit uses an IM 310 and its own power supply. When reviewing the rack arrangement, mark which units belong to the distributed line and which belong to the short centralized connection.
Centralized connection and 5 V power budget
The centralized connection has a 2 m maximum total cable length from the controller to the last local unit. Internal supply is 5 V DC ±5%; the system manual’s IM 301-5CA table specifies 0.75 A maximum module consumption. Include the local expansion-unit loads when sizing the S5 power supply.
A separate 5 A maximum per interface applies to centralized power transfer. Calculate the module’s 0.75 A consumption separately from the load supplied to the expansion units. The 200 m distributed data connection does not supply the remote unit’s operating power.
Termination and cable connections
Fit the 6ES5 760-0AA11 terminator to an unused lower distributed connection and to the last IM 310 in the chain. Trace the upper centralized connection separately; connector appearance alone does not identify its function.
Equipotential bonding matters for the IM 301 / IM 310 connection. Check grounding, shield contact and connector fastenings. When investigating electromagnetic interference, assess routing near power cables together with the reference connections between cabinets.
Addressing and I/O scope
The IM 301 / IM 310 connection supports I/O modules and suitable IP modules without page addressing. Compare the addresses used in the controller, local units and remote units against the PLC program; avoid duplicate I/O addresses.
Test access to digital inputs, digital outputs and analog modules separately. Check the IM 301 address-area jumpers against the diagram for its hardware version, and record their positions before replacement.
Fault indicators and commissioning
The manufacturer associates the red LED 1 / LED 2 indications during CPU restart with loss of internal 5 V or external 24 V load voltage. During troubleshooting, assess the LEDs together with CPU status and actual supply measurements.
In a Siemens S5 system, inspect the upper centralized path and lower distributed path separately. After verifying the cables, supplies, termination and address allocation, test I/O access through both connections.
Editor’s note
Start with the suffix: this is 301-5CA12. The upper centralized connection has a different power arrangement from the 301-3AB13. Record the existing cable positions before moving them, even when the two sockets look alike.
Label the cables “upper: centralized” and “lower: distributed” before disconnecting them. Record the order of the remote units too. A short written record saves a great deal of cable tracing later.
A 200 m rating does not apply to every connection. Build the local path within its 2 m total limit and the remote path within its 200 m total limit. Include the short intermediate sections; measuring only the longest cable is not enough.
If the fault appears when outputs are loaded, pause before replacing the interface. Measure the 5 V rail under load and check the local units’ current demand. Correct termination does not resolve a supply drop, so keep those checks separate.
When buying a used Siemens card, ask for more than a CPU reaching RUN. Verify both the IM 310 distributed path and the IM 312-5 centralized path on a suitable setup. Keep the cable, terminator and test addresses with the result.
OtomasyonAVM resources and PDFs
+ S5 interface modules · IM 310 expansion interface · 760-0AA11 terminator
+ Siemens S5 shared PDF archive and manuals. Manufacturer references for the centralized and distributed connection diagrams are provided below.
Related topics
+ 6ES5 312-5CA11 · 6ES5 312-5CA21 · 6ES5 184-3UA11
+ 6ES5 310-3AB11 · 6ES5 183-3UA13 · 6ES5 301-3AB13
Browse SIMATIC S5
+ S5 interface modules · S5 racks · SIMATIC S5
+ Siemens S5 PLC · Siemens second-hand equipment
Siemens and external references
+ Siemens S5-135U/155U System Manual – English; C79000-G8576-C199-07. Section 7.2 covers upper/lower connections, I/O scope and LEDs; section 7.4, PDF page 311, gives the IM 301-5CA supply and current table.
+ Siemens ST 50, 1998 – English; S5-135U/155U/H catalog section. Printed page 4/142 identifies the exact 301-5CA12 code, IM 310 pairing and 760-0AA11 ordering entries.
+ Siemens U Periphery – English; U-Series Installation Guide, B8576452-03. Printed page 1-6 / PDF page 337 covers the IM 301-5C / IM 310-3 chain, 200 m and 760-0AA11 on the last IM 310; page 7-4 covers equipotential bonding.