6ES5 435-7LA11
Siemens 6ES5 435-7LA11 — 16-Channel 115 V AC/DC Digital Input Module
6ES5 435-7LA11 is a 16-channel, optocoupler-isolated digital input module for the S5-115U in the Siemens SIMATIC S5 family. Its digital inputs are arranged in four groups of four. The rated signal class is 115 V UC (AC/DC), with a specified AC frequency range of 47–63 Hz.
It transfers 115 V contact and status signals to the PLC in SIMATIC S5 installations. Each four-input group shares a return connection. The related 16-channel 435-7LB11 uses groups of two; LA11 and LB11 must not be assumed to have identical shared-terminal arrangements. Do not apply the voltage ratings of a 230 V input card to this model.
Signal levels and input current
Logic 0 is defined as 0–40 V and logic 1 as 85–135 V. 40–85 V is not a guaranteed logic state. Typical logic-1 input current is 15 mA with 50 Hz AC or 6 mA with DC. These figures describe the current the signal source supplies to the input circuit.
When reading a relay or contactor state through an auxiliary contact, check the contact-circuit voltage together with the relevant group return. With interposing relays and sockets, assess the coil supply separately from the signal circuit feeding the PLC. A standard 24 V DC sensor output cannot directly provide logic 1 to this input.
Response time and two-wire sensors
Response time is 2–13 ms from 0 to 1 and 10–25 ms from 1 to 0. Include both input delay and PLC scan time when assessing short pulses. These standard inputs should not be treated as high-speed counter inputs.
Siemens supports suitable two-wire BERO proximity switches and specifies a 5 mA quiescent-current value. Check sensor operating voltage, off-state leakage and input thresholds together; a two-wire connection alone does not establish compatibility.
Group isolation and phase connections
Galvanic isolation is provided between four-input groups; the 16 channels are not all individually isolated. The manufacturer’s footnote for this model permits different phases between separate groups. Follow the wiring diagram while preserving shared returns within each group and the 115 V input limits.
Rated isolation voltage between groups is 250 V, with a specified test voltage of 1500 V. Isolation test voltage is not a permissible operating voltage for the inputs. Do not transfer another S5 card’s phase or shared-terminal rules directly to this module.
Front connector and cable conditions
Within the 46-pole connector family, 490-7LB21 has screw terminals and 490-7LA11 uses crimp connections. When inspecting S5 cables and connections, compare connector type, input channels and all four group returns with the installed wiring diagram.
The manual specifies maximum cable lengths of 1000 m shielded or 600 m unshielded. Assess these values alongside the installation’s cable-routing and electromagnetic compatibility requirements.
Installation, addressing and temperature
Check the suitable S5 rack, interface modules and expansion arrangement against the system manual. The 16 inputs provide two bytes of signal information. Verify the start address in the PLC program against the actual installation and input/output assignment; the order code does not determine a fixed address.
At 135 V input voltage, the specified per-group simultaneity factor is 100% at 25 °C and 75% at 55 °C. Typical module power loss is 11 W. During fault diagnosis, assess cabinet temperature, active inputs and actual signal voltage together, and establish safe machine conditions before measurements.
Differences between related modules
435-7LC11 has eight 115 V UC inputs in individual groups; 436-7LA11 has sixteen 230 V UC inputs in groups of four. 430-7LA12 has thirty-two 24 V DC inputs. These cards are not direct equivalents unless channel count, signal voltage and group wiring match the application.
Editor’s note
Start by establishing the 115 V input class. The 435 and 436 codes look similar, but their voltage ratings differ. Check the label and the incoming field signal together before changing the card.
If four channels fail together, do not immediately assume four separate faults. This module uses groups of four; inspect that group’s shared return and connector contacts first. One loose connection can make several healthy inputs appear faulty.
If an input LED is unstable, look beyond the flashing light. The logic-1 range is 85–135 V; if the signal falls between defined ranges, investigate the source and cable first. Replacing the card will not correct a low signal voltage.
Different phases are permitted between groups on this model, but preserve the group returns and 115 V limits according to the diagram. Do not copy a jumper arrangement from another card out of habit.
For a used card, check all 16 channels, all four group returns and the connector individually. Remember simultaneous-input conditions in a warm cabinet too. Photograph the label and address records before removal so the next maintenance visit starts with clear information.
OtomasyonAVM resources and PDF files
+ S5 PDF files and user manuals · About Siemens S5 PLCs. The main reference is the S5-115U Manual, EWA 4NEB 811 6130-02b, Edition 04. Exact-model specifications and wiring are on printed page 15-25 / PDF 553; front connector options are on 15-66 / PDF 594. The document is in English.
Related topics
+ 435-7LB11 groups of two · 435-7LC11 eight inputs · 436-7LA11 230 V input · 430-7LA12 24 V DC input · 490-7LB21 screw-terminal connector.
Browse SIMATIC S5
+ S5 digital input modules · S5 racks · S5 interface modules · Siemens S5 PLC · Siemens second-hand equipment.