6ES5 463-4UB12

Siemens 6ES5 463-4UB12 – 4-Channel Analog Input Module, 60 Hz

Siemens 6ES5 463-4UB12 is a four-channel, galvanically isolated analog input module in the SIMATIC S5 analog module range, used in S5-115U and S5-135U/155U applications. Nominal ranges are 0–1 V, 0–10 V, 0–20 mA and 4–20 mA. Its integration time is 16⅔ ms for 60 Hz environments.

It transfers continuous measurements from analog sensors to the PLC. Typical sources include suitably rated pressure transmitters and temperature signal converters. The transmitter output, channel wiring and software scaling must agree.

Input ranges and wiring

Each channel range is selected through front-connector wiring and jumpers. A 0–10 V sensor and a 4–20 mA sensor require different connections. Record the existing jumper arrangement before transferring the connector.

For voltage measurement, the 10 V input resistance is 90 kΩ. For current measurement, it is 50 Ω at 0–20 mA and 62.5 Ω at 4–20 mA. The measuring shunts are fitted inside the module.

Choose the 0–10 V or 4–20 mA interface to match the field device. Temperature sensors may require a suitable transmitter; use the voltage/current ranges specified for this module.

Isolation and power supply

All four inputs are isolated from each other and from M. The maximum permitted reference-potential difference is 25 V AC / 60 V DC. Connecting a two-wire transmitter’s Common input to L− removes isolation between that channel and the field supply. Review the grounding arrangement accordingly.

The digital section draws 5 V, typically 150 mA, from the system bus. The analog section requires 24 V DC, approximately 150 mA. With the enable jumper fitted, F+/F− also requires 24 V. Removing the jumper disables the external enable function.

When inspecting S5 cables and connectors, check the shield connections too. Routing measurement wiring separately from power cables helps reduce electromagnetic interference.

Scaling and addressing

Measured values use 11-bit two’s-complement representation with 1024 units across the nominal range. Each 4–20 mA channel can select 0…1023 or 256…1279 representation. Match the scaling in the PLC program to that setting.

The four channels occupy 8 bytes. For analog I/O addressing, the start address is a multiple of eight; the channel words are read at A, A+2, A+4 and A+6.

When checking an analog signal, account for the different interpretation of analog and digital inputs. Verify the raw measurement, engineering-unit conversion and alarm limits separately.

System compatibility and installation

Siemens ST 50 lists this code for S5-115U/H/F; the S5-135U/155U system manual also covers the exact model. Check the rack, adapter and slot requirements of the Siemens S5 system. H/F installations remain subject to their system-specific requirements.

It uses a 42-pole type 497 front connector: 6ES5 497-4UA12 for crimp terminals or 6ES5 497-4UB31 for screw terminals. Confirm whether the connector is included with the module.

Editor’s note

Start with the complete label: 4UB12 is the 60 Hz version. Take a moment to compare it with the 50 Hz 4UA12, even if the housings look alike. Reading the full code now is easier than tracing a mismatch later.

Photograph the connector jumpers and switch settings before removing the old module. In a current circuit, jumper contacts and additional connections can affect the reading. Check those small details before condemning an otherwise serviceable card.

If the PLC cannot access the module, check the 24 V field supply, enable jumper and F+/F− voltage where required first. This gives your PLC troubleshooting a clear starting point before arranging a replacement.

If a 4–20 mA reading appears offset, check the channel’s representation switch first. Apply the same current to the old and replacement cards and compare their raw readings. Establish that both use the same setting before investigating calibration.

When buying a used analog module, ask for more than confirmation that the PLC detects it. Test all four channels at low, middle and high points, then repeat after warm-up where practical. A simple test record makes the condition much easier to judge.

OtomasyonAVM resources and PDFs

+ Browse our Siemens S5 PLC overview and S5 analog module pages for system and module information.

+ Siemens S5 shared PDF archive and manuals. Manufacturer documents containing the exact 463-4UB12 technical tables are linked in the external references below.

Related topics

+ 6ES5 463-4UA12: the 50 Hz version of this 463 family. 6ES5 463-4UA11: an earlier 50 Hz version; review the complete code and enable-circuit requirements when planning a replacement.

+ Used analog-output sensors: match the sensor output range to the channel setting.

Browse SIMATIC S5

+ S5 analog modules · SIMATIC S5 · Siemens S5 PLC

+ Siemens second-hand equipment · Used analog modules

Siemens and external references

+ Siemens S5-135U/155U System Manual – English; §9.4, enable circuit, addressing and technical specifications.

+ Siemens U Periphery – English; §5.3, technical tables for 463-4UA11/12 and 463-4UB11/12.

+ Siemens ST 50, 1998 – English; page 3/47, S5-115U/H/F ordering data and 497 front connectors.