6ES5 310-5AA12

Siemens 6ES5 310-5AA12 — IM 310-5 Distributed Interface Module

The Siemens 6ES5 310-5AA12 is an IM 310-5 interface module for distributed expansion in SIMATIC S5 systems. Siemens ST 53 identifies it as the Robustbauform version for connections with a total length of up to 200 m. In the S5 interface range, it serves the expansion-unit side.

Its application group is the EG 182-3A expansion unit. Record the full chassis number and interface position. For this arrangement, the catalogue shows the IM 310-5 in slot 2 of the EG 182-3A.

IM 301 matching and 721 cable

The Robust central-side arrangement uses a 301-5AA13. A 301-5CA12 arrangement is specified separately for connecting a compact central controller to a Robust expansion unit. Compare both ends before selecting a replacement.

The connection uses a 721 cable; the catalogue diagram allows up to four EG 182 units and 200 m total to the last unit. When checking the cable, include connectors, shielding and cabinet grounding alongside its length.

Selecting the terminator

The last IM 310-5 on the distributed line requires a 6ES5 760-0AA11 terminator. Record its position and connector condition before replacing parts. A small accessory lost during removal can make troubleshooting unnecessarily difficult.

Distinguish 310, 311 and 312 codes

The 310-3AB11 is the catalogue’s compact version. Do not treat it as the same physical construction as the 310-5AA12. Compare labels, chassis and connector photographs before deciding on interchangeability.

The 312-5AA13 and 312-5AA31 belong to centralized connections. Review arrangements using a 300-5AA12 separately from the distributed 301/310 line. Similar front panels do not establish the same connection role.

Where 312-5CA12, 312-5CA22 and 300-5CA11 appear in an installation, identify the chassis and cable belonging to each interface. Do not group every “31x” board together as interchangeable spares.

The 311-3KA11 belongs to the 302/311 remote-link group. That group’s 1000 m specification does not apply to the 310-5AA12. This product is listed for the 200 m 301/310 arrangement.

Replacement and fault investigation

Keep the S5 system’s chassis list, connection sequence and PLC program addresses together. During troubleshooting, record the first inaccessible unit. Check the cable, connectors, supply and board in a clear sequence to narrow the fault.

Editor’s note

On an installation of this age, the complete label matters. A request for a “310 board” leaves too much room for error. Record the 5AA12 suffix and its chassis together before ordering.

Photograph the original connections and mark both ends of each cable. When the work gets complicated, a clear record is much easier to rely on than memory.

A loose connector screw, bent pin or damaged cable entry can look like a board fault. Take a little time over these small details before setting a sound module aside.

Back up the program before removal. Switch off power and follow the system instructions for replacement. A few minutes spent recording the original arrangement can save hours later.

For used equipment, ask where possible for a working test with a suitable central controller, expansion unit and cable. Knowing how the assembly was tested is as useful as seeing its condition. Agree on that at the outset so everyone knows what has been checked.

OtomasyonAVM resources and PDFs

+ About Siemens S5 PLCs · S5 interface modules

+ Siemens S5 PDF files — our manual archive. Siemens ST 53 references for this older Robust version’s exact ordering code and connection arrangement appear below.

Related topics

+ 301-5AA13 · 301-5CA12 · 760-0AA11 terminator · 310-3AB11 compact version

Browse SIMATIC S5

+ S5 interface modules · S5 racks · S5 cables · SIMATIC S5 · Siemens second-hand equipment

Siemens and external references

+ Siemens ST 53, 1985 — 9/3: exact 6ES5 310-5AA12 code, Robust/compact versions and terminator (German)

+ Same catalogue — 2/9: IM 301/310 connection, 721 cable, 200 m limit and slot position

+ Same catalogue — 2/5, Figure 2/2: distributed EG 182 connection diagram