6ES5 945-7UA23

Siemens 6ES5 945-7UA23 — S5-115U CPU 945, 384 Kbytes RAM

Siemens 6ES5 945-7UA23 is a CPU 945 central processing unit for SIMATIC S5-115U. Siemens ST 50 lists the exact part number with 384 Kbytes of internal user RAM. This CPU in the Siemens S5 family executes machine-control logic, arithmetic and communications tasks.

Field signals are handled through separate digital input and digital output modules. The CPU 945 rating of 1024 inputs and 1024 outputs in the process image describes system addressing capacity, not physical channels built into the processor.

384 Kbytes of RAM and non-volatile program storage

Internal RAM holds the working user program and data. Retaining RAM contents during a power failure depends on the system’s backup arrangement. A removable S5 memory card provides non-volatile program storage and transfer; these memory types serve different purposes.

The CPU 945 ordering table includes short-format Flash EPROM cards such as 6ES5 374-1KH21 — 256 Kbytes. This card does not expand the CPU’s RAM. Do not assume that a 256 Kbyte card can hold the complete application occupying the 384 Kbyte memory. The manual specifies PG software V6.6 or later for this card group.

SI1 TTY connection and replaceable SI2

The integral SI1 connection uses a 20 mA TTY current-loop interface for PG, OP and suitable SINEC L1 links. Select the interface and programming cable for the required electrical connection. A separate receptacle accepts a replaceable submodule for SI2.

Siemens lists the 6ES5 752-0LA12 TTY, 6ES5 752-0LA52 PG and 6ES5 752-0LA62 SINEC L1 options for CPU 945. Do not confuse these 0LA part numbers with 0AA submodules used by other CPUs. Evaluate the second port’s protocol together with its fitted submodule and software parameters.

STEP 5, instruction timing and internal resources

Programming uses STEP 5, with SCL also available in a suitable software arrangement. The catalogue specifies 0.1 µs for a bit operation. This is an individual instruction time, not the complete PLC scan time of a machine application.

CPU 945 provides 256 timers, 256 counters and an integral real-time clock. The catalogue gives a 1 ms to 1 minute call interval for time-controlled OB 10–OB 13 execution. In an S5 application, interrupts, communications and peripheral accesses also affect overall execution time.

Rack installation, supply and consumption

The processor fits a suitable S5-115U central rack. CR 700-3 / 6ES5 700-3LA12 is one central-rack option used by the system. CPU 945 weighs approximately 0.8 kg; assess installation and power requirements together with the other fitted modules.

Power is supplied through the PS 951 power supply and system connections. Without an interface submodule, the manual gives typically 0.5 A from the internal 5 V rail, 0.06 A from the 24 V rail and typical power dissipation of 4.2 W. These figures are not instructions to apply an arbitrary external 24 V supply to the CPU. A fitted SI2 submodule changes the consumption calculation.

Diagnostics and other CPU 945 part numbers

During fault-finding, examine RUN/STOP together with QVZ, ZYK and BASP indications. Check the program backup, power-supply battery warning, connections and communications parameters before proceeding with an overall reset or CPU replacement.

6ES5 945-7UA13 is the 256 Kbyte option in the catalogue, while 7UA23 provides 384 Kbytes. 6ES5 945-7UA21 is another CPU 945 order number. A shared CPU name or memory size does not establish direct equivalence between hardware and operating-system revisions.

Editor’s note

For used Siemens equipment, check the 7UA23 label, revision and exact SI2 submodule number together. Two CPUs can look alike while carrying different communications hardware.

Back up the program, data blocks and port settings before removing power. Record any battery warning so that a later loss of memory does not obscure the original fault.

For a Flash card, verify the short format, capacity and PG software version. Inserting a 256 Kbyte card does not demonstrate that it contains the complete application running in 384 Kbytes of RAM.

Switch the system power off before replacing the SI2 submodule. Siemens prohibits inserting or removing this component while powered. Avoid forcing aged connectors or securing screws.

Complete the test by checking PG access, OP or field communications and startup following a controlled power cycle under suitable conditions. Record the results together with the cable and submodule part numbers.

OtomasyonAVM resources and PDFs

Browse the 6ES5 945-7UA23 model page, SIMATIC S5 CPU family and used Siemens equipment. General documents are collected in the shared Siemens S5 PDF archive. The English CPU 945 manual and exact-code Siemens catalogue are linked below.

Related topics

+ 6ES5 945-7UA13 — 256 Kbyte CPU 945 option.

+ 6ES5 945-7UA21 — another CPU 945 code requiring revision comparison.

+ 6ES5 945-7UA11 — a different CPU 945 order version.

+ 6ES5 374-1KH21 — 256 Kbyte short-format Flash EPROM card.

+ 6ES5 752-0LA52 — PG interface submodule for CPU 945.

Browse SIMATIC S5

S5 CPUs · S5 racks · S5 memory cards · S5 interfaces · Siemens S5 PLC · Used Siemens equipment

Siemens and external references

Siemens ST 50 — SIMATIC S5 Catalog, 1998 — Printed pp. 3/24–3/26 / PDF pp. 110–112: exact 7UA23 code, 384 Kbytes RAM, interfaces and memory cards; instruction times, internal resources and weight.

Siemens S5-115U CPU 945 Manual — 6ES5 998-3UF21, Edition 06 — English manual. PDF p. 37: Flash cards and PG software requirement. Section 12.7 / PDF p. 524: interface-submodule replacement only with power off. Section 15.2.3 / PDF p. 600: CPU consumption and weight.