6ES5 752-0LA62
Siemens 6ES5 752-0LA62 — SINEC L1 Interface Module for CPU 945
6ES5 752-0LA62 is a SINEC L1 interface submodule for the second serial interface (SI2) of the S5-115U CPU 945. It has a 15-pin Sub-D socket and supports rates up to 9600 bit/s. The SIMATIC S5 catalog lists it among the interface options for CPU 945 6ES5 945-7UA13 and 6ES5 945-7UA23.
It connects the CPU 945 to a SINEC L1 network or a point-to-point link using the SINEC L1 protocol. With suitable parameterization, it also supports programmer access, the ASCII driver and a 3964(R) computer link. For industrial communications, match the operating mode, cable and CPU program; installing S5 communications hardware is only one part of commissioning.
L1 network and point-to-point operation
A multi-node SINEC L1 network has one master and up to 30 slaves. A CP 530 handles the master role; the CPU 945 can join as a slave through SI2 and this submodule. Each network node requires a BT 777 level converter, connected by a shielded four-wire bus cable.
Record the exact codes and cables of installed connection components, such as BT 777 6ES5 777-0BB01 and 6ES5 777-0BC01. The CPU interface, BT 777 and bus wiring must be checked as one communications path.
For point-to-point operation, the CPU 945 can act as master through SI2. Set the CPU station number to 0 and the partner to 1. In this mode, the SI2 communications port cannot simultaneously provide programmer/OP access. An ASCII or 3964(R) link must not remain active on the same interface.
Connector and cable arrangement
The front connector is a 15-pin female Sub-D. The main signal assignments are TXD: 6(+)/7(−), RXD: 9(+)/2(−). The connector also carries 24 V and current-source connections. When preparing an S5 connecting cable, use Siemens Figures 12.42 and 12.44 rather than relying on connector shape.
For a direct point-to-point line, Siemens specifies 1000 m maximum, shielded four-wire cable and a minimum conductor cross-section of 0.14 mm². This applies to the documented circuit, rather than to every programmer cable or network topology. Compare the module’s jumper arrangement with Figure 12.43 as well.
Parameters and data exchange
L1 communication requires a station number, send/receive areas and coordination bytes. Each send or receive mailbox holds up to 64 bytes of data. Match the DB1 parameters or applicable startup routines in the STEP 5 program to the existing application.
An online connection in the programming software is only a starting point: verify data from the correct partner and the send/receive coordination. During troubleshooting, check wiring, station number, active driver and data areas in sequence. The 9600 bit/s limit does not mean every application value is refreshed during every PLC scan.
Comparison with related 752 modules
6ES5 752-0LA12 is the 20 mA/TTY option; 6ES5 752-0LA52 is the programmer-interface option. Verify 0LA62 for the required SINEC L1 or L1 point-to-point function. For similarly numbered parts such as 752-0AA62, also check the host CPU and receptacle; keep the AA and LA order-code families distinct.
Insert or remove the submodule only with CPU power switched off, and secure it with its fixing screws. Isolate the S5 power supply before working on the module. Record the CPU code, operating-system version and interface label in the existing S5 installation.
Before replacement, back up the program, communications parameters and details of the fitted S5 memory card. Preserve the CPU 945 application by checking the original operating mode and data exchange again after installing the replacement.
Editor’s note
When choosing a replacement, take the time to find 0LA62 on the label and CPU 945 on the host. A small suffix difference can mean a very different interface, even when the parts look familiar.
If communication stops, work through the cable, BT 777 and partner station before condemning the submodule. One damaged conductor or loose connector can make a healthy card look faulty.
Check the network arrangement before changing the master setting. A multi-node bus with CP 530 and a two-device CPU 945 link use different arrangements. Keep a record of the working addresses before changing them.
A clean used module still needs a communications test. Where possible, use a suitable CPU and known-good cable, send and receive data, and watch the link for a while. Establishing a connection and transferring correct data are separate checks.
Photograph the label, jumpers and cable ends before removal. Switch the power off for installation and seat the fixing screws properly. On an older machine, these small records can save a long fault-finding session later.
OtomasyonAVM resources and PDFs
+ S5 interface modules · CPU 945 7UA13 · CPU 945 7UA23 · About Siemens S5 PLCs.
+ OtomasyonAVM S5 PDF archive. For this module, see CPU 945 manual sections 12.3, 12.4 and 12.7.5–12.7.6. The manufacturer documents below are in English.
Related topics
+ CP 530 and the SINEC L1 network · BT 777 0BB01 · BT 777 0BC01 · S5 cables and connectors.
+ 752-0LA12 TTY interface · 752-0LA52 programmer interface · S5 communications modules.
Browse SIMATIC S5
+ S5 interface modules · SIMATIC S5 · Siemens S5 PLC · Siemens second-hand equipment.