RCM Standards

RCM Regulatory Compliance Mark Australia New Zealand electrical and electronic equipment

What is RCM? RCM stands for Regulatory Compliance Mark. It is a compliance mark used in Australia and New Zealand for certain electrical, electronic, radiocommunications and telecommunications products.

The RCM indicates that the supplier has addressed the regulatory requirements that apply to the product under the relevant compliance scheme. Depending on the type of equipment, these requirements can involve electromagnetic compatibility (EMC), radiocommunications, telecommunications, electromagnetic energy exposure and electrical safety.

The RCM is not itself a technical product standard and it is not a general quality certificate. It is a regulatory compliance mark used within defined Australian and New Zealand regulatory frameworks.

For other country-specific approval systems, see our global standards and conformity systems section.

In Simple Terms: What Does RCM Mean?

Imagine that you want to sell an electronic controller in Australia. It is not enough for the controller simply to work. You may also need to show that it does not create unacceptable radio interference, that it meets applicable electrical-safety rules and that the required technical records and supplier registrations are in place. Once the relevant compliance steps have been completed, the RCM can be used where required. In simple terms, the mark says: “The applicable Australian or New Zealand regulatory requirements for this product have been addressed, and a responsible supplier stands behind that compliance.”

Is RCM a Standard?

No. Although people often search for “RCM standard,” the RCM itself does not define technical requirements in the way that an IEC, ISO or product standard does.

The use and physical presentation of the mark are associated with Australian/New Zealand requirements such as the AS/NZS 4417 series, while the actual technical standards that apply to the equipment depend on the product and regulatory scheme.

This is an important distinction within industrial standards: a technical standard defines requirements; a regulatory mark indicates compliance within a particular regulatory framework.

Did RCM Replace C-Tick and A-Tick?

Yes. The former Australian compliance marks known as C-Tick and A-Tick are legacy marks. The RCM became the principal compliance mark used under the newer Australian regulatory labelling framework.

This is why older variable frequency drives, PLCs, power supplies and industrial controllers may still carry the C-Tick mark in their manuals or on their nameplates.

A C-Tick mark on an older product is not necessarily an error; it reflects the compliance system in use when that product was supplied. It should not, however, be treated as the current mark for newly supplied equipment.

What Requirements Can the RCM Relate To?

The meaning of the RCM depends on which regulatory scheme applies to the product.

In Australia, the Australian Communications and Media Authority (ACMA) regulates areas including electromagnetic compatibility, radiocommunications, telecommunications and certain electromagnetic energy requirements.

Electrical-equipment safety can also fall within the Electrical Equipment Safety System (EESS) in participating Australian jurisdictions.

In New Zealand, radiocommunications and EMC product compliance is administered through Radio Spectrum Management (RSM).

You therefore need to know which regulatory framework applies before interpreting what the RCM represents for a particular product.

What Is ACMA?

ACMA – Australian Communications and Media Authority is the Australian regulator responsible for areas including communications, radio spectrum and regulatory requirements applying to certain electrical and electronic products.

If a product falls within ACMA's equipment rules, the supplier must determine the applicable requirements, demonstrate compliance, maintain the required records, register where required and correctly label the product.

ACMA describes this through a five-step supplier process:

1. Check the rules that apply.
2. Show that the product complies.
3. Sign and keep the required records.
4. Register as a responsible supplier where required.
5. Label the product correctly.

What Is EESS?

EESS – Electrical Equipment Safety System is a regulatory system for electrical equipment supplied in participating Australian jurisdictions.

Within EESS, in-scope electrical equipment can be classified according to risk as Level 1, Level 2 or Level 3. The compliance evidence and registration requirements increase according to the classification.

Level 2 and Level 3 equipment require product registration under the EESS framework, while Level 3 equipment requires a valid Certificate of Conformity. Level 1 equipment follows less demanding product-registration requirements, although supplier and compliance responsibilities still apply.

Not every industrial electronic product automatically falls within EESS scope. The equipment type, electrical characteristics and the jurisdiction in which it is supplied must be checked.

What Is a Responsible Supplier?

The concept of the Responsible Supplier is central to the RCM framework.

For Australian ACMA-regulated products, the supplier can be an Australian manufacturer, importer or agent responsible for placing the product on the Australian market and meeting the applicable regulatory obligations.

Under EESS, the registered Responsible Supplier is linked to the equipment and is authorised to apply the RCM where the applicable requirements have been met.

For New Zealand RCM use, suppliers register through the shared ERAC supplier system and obtain a supplier number before using the RCM under the relevant RSM framework.

Can an Overseas Manufacturer Simply Put the RCM on a Product?

Not simply by printing the logo. An overseas manufacturer supplying equipment to Australia or New Zealand must make sure that the appropriate supplier, registration, technical-evidence and labelling requirements are satisfied for the target market.

For Australia, an importer or authorised Australian agent may carry regulatory responsibilities. For electrical equipment subject to EESS, the Responsible Supplier structure and registration requirements are particularly important.

For this reason, an overseas machine builder or industrial-electronics manufacturer should plan the RCM process together with the party responsible for placing the equipment on the Australian or New Zealand market.

How Does the RCM Compliance Process Work?

The exact process depends on the product, but a practical sequence is:

Identify the product → determine which regulations apply → identify the technical standards → obtain the required compliance evidence → prepare and retain declarations and technical records → complete supplier and product registration where required → verify labelling requirements → apply the RCM.

This is why the phrase “obtain an RCM certificate” is generally misleading. There is no single universal RCM certificate that every product receives.

Depending on the equipment and scheme, the evidence may involve test reports, a Supplier Declaration of Conformity, EESS registration or an independent Certificate of Conformity. The RCM itself is the compliance mark used after the relevant obligations have been satisfied.

Does Every Product Need Laboratory Testing?

The required evidence depends on the product and the applicable regulatory framework. ACMA states that most regulated products require testing to demonstrate compliance, but the level and type of evidence vary.

Higher-risk electrical equipment and higher conformity levels can require stronger evidence, including reports from recognised or accredited laboratories.

Therefore, neither “every RCM product must always be tested by an accredited laboratory” nor “no independent testing is needed for RCM” is a safe general rule.

What Is a Supplier Declaration of Conformity?

SDoC – Supplier Declaration of Conformity is a document in which the responsible supplier declares that the product meets the applicable technical requirements.

Under Australian ACMA rules, suppliers must sign and retain the required compliance records. In New Zealand, an SDoC and supporting evidence can also form part of the product-compliance framework depending on the applicable conformity level.

The declaration does not replace the technical evidence. A declaration is meaningful only when the required evidence exists behind it.

Does the Supplier Number Need to Be Printed Beside the RCM?

Older compliance systems commonly used separate approval or supplier-identification numbers on equipment.

Under the current EESS marking system, the RCM links the equipment to the registered Responsible Supplier through the registration database. The previous requirement to separately mark a unique approval or certificate number on the product was removed under the newer system.

Physical RCM marking requirements are addressed through standards including AS/NZS 4417.1 and AS/NZS 4417.2. Under ACMA rules, alternative electronic or linked labelling methods may also be available for certain products where the applicable rules permit them.

Does CE Marking Replace the RCM?

No. European CE marking does not automatically demonstrate compliance with Australian regulatory requirements and does not automatically authorise use of the RCM.

International or European test reports may sometimes be accepted as part of the evidence where they demonstrate compliance with the applicable Australian or New Zealand technical requirements.

However, this still does not mean that a CE-marked product can simply be placed on the Australian market without completing the relevant RCM compliance steps.

CE and RCM belong to different regulatory systems.

Is the RCM a Quality Mark?

No. The RCM should not be described as proof that a product is higher quality, more durable or more reliable than competing equipment.

The mark indicates compliance with applicable regulatory requirements within the relevant framework. Product lifetime, manufacturing quality, industrial performance and suitability for a particular application are separate matters.

For this reason, statements such as “RCM-certified products are higher quality” should be avoided.

Why Is RCM Important in Industrial Automation?

A PLC, HMI, variable frequency drive, industrial power supply, sensor, controller or communications device supplied to Australia or New Zealand may need to be assessed against the regulatory rules applicable to that product.

Power-electronic equipment such as variable frequency drives can generate conducted and radiated electromagnetic disturbances, so EMC requirements can be particularly important.

For drive systems, the IEC 61800 series, including IEC 61800-3 for EMC, can provide important technical product-standard requirements.

However, a drive being tested to IEC 61800-3 does not by itself complete the Australian or New Zealand market-compliance process. Technical standard compliance and regulatory market obligations must be considered together.

Does RCM Apply to the Complete Machine or Only to Components?

There is no single answer for every product. The applicable rules depend on what equipment is being supplied and which regulatory scheme applies.

Using an RCM-labelled power supply, PLC and drive inside a machine does not automatically demonstrate that the completed machine complies with every Australian or New Zealand requirement.

The completed equipment can still have its own EMC behaviour, radio functions, electrical-safety issues or other regulatory obligations that require assessment.

As with other conformity systems, compliant components do not automatically make the complete machine compliant.

How Is the RCM Used in New Zealand?

New Zealand's EMC and radiocommunications product-compliance framework is administered by Radio Spectrum Management (RSM).

Products subject to RSM requirements are assigned conformity levels that determine the type of technical evidence, declaration and labelling required.

For EMC and radiocommunications products in conformity levels 1, 2 or 3, New Zealand uses the RCM. Certain radio transmitters that fall within New Zealand-specific conformity classes use the R-NZ mark instead.

This means that RCM is not automatically the correct label for every radio product supplied in New Zealand.

What Does C-Tick Mean on Older Industrial Equipment?

If an older drive, PLC or power supply carries the C-Tick, it may simply indicate that the product was supplied under the Australian/New Zealand EMC labelling framework in use at the time.

This does not automatically mean that the equipment is counterfeit or non-compliant. It does mean that the mark should be interpreted in its historical context.

C-Tick is not the current compliance mark for newly supplied Australian equipment.

How Can RCM Compliance Be Checked?

Seeing the RCM symbol on a product is only one part of the compliance picture. Depending on the scheme and equipment type, it can also be useful to verify the Responsible Supplier, product registration, model identification and supporting compliance documentation.

For higher-risk electrical equipment, certificate and registration information can be especially important.

An RCM logo is easy to print. Real compliance is demonstrated by the registration and technical evidence behind the mark, not by the artwork alone.

Common RCM Mistakes

“RCM is a certification.” Not quite. The RCM is a regulatory compliance mark.

“A CE-marked product does not need RCM.” Incorrect. Overseas markings do not automatically replace Australian compliance requirements.

“RCM proves high product quality.” Incorrect. It is not a general quality ranking.

“Every electrical product follows exactly the same RCM process.” Incorrect. ACMA, EESS and New Zealand RSM requirements depend on the type and classification of the product.

“An overseas manufacturer can simply print the logo.” Incorrect. Supplier responsibility, registration and compliance evidence may also be required.

“C-Tick is still the current Australian mark.” Incorrect. C-Tick and A-Tick belong to the previous marking system.

Where Should the RCM Compliance Process Start?

The process should not begin by downloading the RCM logo.

Identify the product → determine the applicable Australian or New Zealand regulatory framework → identify the technical standards → obtain the required test and compliance evidence → prepare declarations and records → complete supplier and product registration where required → verify the labelling rules → apply the RCM.

The RCM is the visible result of the compliance process, not the beginning of it.

Important: RCM requirements depend on the type of equipment, its technical characteristics, risk classification and the regulatory framework under which it is supplied. For a new product entering Australia or New Zealand, the current ACMA, EESS and New Zealand RSM requirements should always be checked.

Related Standards and Compliance Guides

Industrial Standards  •  Global Standards  •  Device Standards  •  IEC Standards  •  EN Standards  •  IEC 61800

Related Automation Guides

Industrial Automation  •  What Is Automation?  •  PLC & HMI