What is Differential output?

Encoder signals: matching differential, TTL and HTL interfaces

A reliable feedback connection starts with the receiver specification. Before choosing from the encoder range, check its signal voltage, transmission arrangement and output circuit. These describe different properties: single-ended or differential explains how the signal is read; TTL or HTL describes its voltage class; push-pull or open collector describes the driver. Our encoder output guide puts these choices in context.

Two channels are not the same as a complementary pair

An incremental encoder uses A and B in quadrature, ideally separated by 90 electrical degrees. Their sequence identifies direction. A−, also written A̅, is the complement of A; it is not B. A differential device may provide separate A/A−, B/B− and Z/Z− pairs. Understanding these pulse signals also prevents confusion with pulse-and-direction commands sent to a drive.

A single-ended receiver reads a signal against its 0 V reference. A differential receiver reads the voltage difference between the two members of a pair. That is why line driver outputs need correctly paired conductors, rather than just additional wires.

Common-mode noise: both lines move, the difference stays In one fixed logic state, an equal 0.6 V is added to A and A minus. The difference remains 2.4 V. These voltages are illustrative. Adding common-mode noise: +0 → +0.6 → +0 V A A− 0 V 4 V A − (A−) +2.4 V Initial state: 2.8 − 0.4 = 2.4 V With disturbance: 3.4 − 1.0 = 2.4 V Restart Stop
A slow illustration of the principle, not a cable-performance or TTL-level simulation. The same voltage is added to both bars. Restart begins a new cycle; Stop holds the picture.

What common-mode rejection actually means

The illustration holds one logic state and adds the same disturbance to both lines: (2.8 + 0.6) − (0.4 + 0.6) = 2.4 V. The ideal difference survives. Unequal interference, an unbalanced cable or exceeded receiver common-mode limits can still cause errors. Differential reception does not provide galvanic isolation by itself. RS-422 specifies electrical signalling characteristics; it does not, on its own, define an encoder position protocol.

Read the signal rating separately from the power rating

TTL and HTL usually mean a 5 V signal class and a 12/24 V signal class, respectively. Actual HIGH and LOW limits depend on the device and load. An encoder powered from 24 V can have TTL/RS-422 outputs. Equally, a 24 V controller can contain a 5 V encoder interface. The power label alone cannot establish compatibility.

Complementary HTL does not automatically meet RS-422 input requirements. A 24 V HTL output needs a suitable receiver or specified converter; it must not be connected to an ordinary 5 V/RS-422 input. Check both the electrical rating and channel arrangement when selecting a PLC, encoder reader or counter and tachometer.

Push-pull drivers actively drive both logic states; the totem pole circuit explains this arrangement. An open collector output needs the appropriate load or pull-up and receiver circuit. These affect its rising edge. An output label is therefore only part of the information needed to wire the device.

Build the cable connection around the interface

Use twisted pairs for A/A− and B/B− separately. Pairing A with B defeats the intended arrangement. Choose termination according to the cable impedance and manufacturer circuit. 120 Ω is a common RS-422 example, not a universal encoder rule. If the input already includes termination, adding another resistor can overload the driver.

There is no single maximum cable length that covers every TTL or HTL encoder. Driver capability, edge timing, cable characteristics and counting frequency all matter. At 3000 rpm, a 1000 PPR encoder produces 50 kHz on A; ×4 decoding gives 200,000 counts per second. Determine which of these quantities your high-speed counter specification limits.

Follow the manufacturer's shield connection instructions rather than applying a blanket one-end rule. High-frequency installations may require 360° shield contact and proper equipotential bonding. Signal 0 V, shield and protective earth serve different purposes. Route feedback away from drive power cables and preserve pair geometry through connectors.

Diagnose the complete feedback path

For missed counts, verify the pin assignment, voltage compatibility, pair allocation and termination before changing software. Inspect the signal at maximum operating speed with suitable differential measurement equipment. A stronger input filter can suppress valid pulses as well as noise. In servo feedback, lost counts can become position errors.

An analog encoder with 0–10 V or 4–20 mA needs an appropriate analog input, rather than a TTL/HTL pulse input. An absolute encoder also needs its specified data interface. Review the encoder basics if comparing measurement methods, and choose suitable mounting accessories alongside the electrical interface.