Delta DVP14ES00R2

Delta DVP14ES00R2 – DVP-ES PLC with 8 Inputs and 6 Relay Outputs

The Delta DVP14ES00R2 is a compact 14-point PLC main unit in the DVP-ES series. It operates from 100–240 V AC, 50/60 Hz. The CPU has 8 digital inputs rated at 24 V DC and 6 relay outputs. Delta’s ES/EX installation sheet lists a program capacity of 3,792 steps. Small conveyors, part feeders and machines with sequential operations are typical PLC applications.

Digital inputs and S/S common

The built-in inputs are addressed X0–X7. An inductive sensor can detect a metal target, a photoelectric sensor can detect a passing part and a limit switch can indicate end of travel. Wire the S/S common according to Delta’s sink/source diagram and the sensor’s NPN or PNP output. Check the normally open or normally closed state against the machine drawing. When tracing PLC I/O, watch the terminal indicator and the corresponding X address together.

Relay outputs and load selection

Outputs Y0–Y5 switch through mechanical relay contacts. Delta’s output table lists 2 A per point, 5 A per common and voltage limits of 250 V AC / 30 V DC. When selecting a load, check the voltage, total group current, inrush and whether the load is inductive. Select suppression for the coil circuit and fuse protection for the output supply. Check cabinet grounding and output commons against the wiring diagram.

To count pulses from an encoder, check the high-speed counter input assignments and limits for the selected counting mode. The mechanical relay outputs respond in approximately 10 ms. If the drive requires a high-speed pulse output, evaluate a transistor-output model with the required terminal and instruction support.

Programming software and cable

Delta WPLSoft is the Windows software specified in the installation sheet. Select the legacy DVP-ES CPU type and COM1 RS-232 to read, back up or monitor the ladder program. If you use ISPSoft, check that your version lists the legacy ES family in its CPU selector.

Delta’s programming cable guide lists the UC-PRG020-12A. This 2 m cable has a female DB9 connector at the PC and a male 8-pin mini-DIN at the PLC. The original installation sheet also lists DVPACAB215 (1.5 m) and DVPACAB230 (3 m). If the PC lacks a serial communication port, install the driver for a USB-to-RS-232 adapter and select the Windows COM port in WPLSoft.

COM2 RS-485 is available for field communication. If an HMI or drive on a Modbus/RS-485 network fails to respond, check the existing program’s protocol, station address, baud rate and parity against the other device. Read the existing program and save a dated copy before online troubleshooting.

Editor’s Note

Ask for a clear nameplate photo when buying a used unit. The DVP14ES00R2 uses AC power. The similarly named DVP14ES01R2 requires 24 V DC.

Start the bench check with the POWER, RUN and ERROR indicators. If the PLC signals a program error, read D1004 in WPLSoft.

If the Y LED lights and the load stays off, check the supply at the output common first. Then test that channel with a suitable low-voltage load on a bench isolated from the machine loads.

If the load stays on after the Y command turns off, isolate the power safely. Disconnect the field wiring and check the relay contact for sticking.

If a relay output has failed, check the coil current, surge suppression and other loads on the same common before installing a replacement. The same cabinet fault can damage the replacement relay.

Keep the program backup, terminal photos and serial port settings together before reinstalling the PLC. When migrating to ES2, check output commons, expansion modules and HMI communications individually.

Related Delta models

The DVP14ES00T2 has the same I/O count with transistor outputs. For more points within the ES series, the DVP24ES00R2 provides 16 inputs and 8 relay outputs, and the DVP32ES00R2 provides 16 inputs and 16 relay outputs. See the DVP08XP11R expansion module for adding 4 inputs and 4 relay outputs to an existing ES system.

Delta introduced ES2 as the successor to DVP-ES. The DVP16ES200R is an ES2 model with 8 inputs and 8 relay outputs. Before migrating, compare the terminal layout, program instructions and expansion support in the documentation for both units.

OtomasyonAVM PDF files and internal references

Delta DVP PLC PDF Files · DVP-ES/EX installation and wiring sheet, 5011634301-YIE1 (English PDF)

Delta PLC overview · Delta DVP PLC series · Used Delta equipment

External references

Delta Electronics – DVP-ES series page · DVP-ES/EX electrical specifications (multilingual PDF) · Delta PLC/HMI Cable Selection Guide, section 1.2 · Delta DVP-PLC Application Manual – Programming