Delta DVP08ST11N

Delta DVP08ST11N – 8-Switch Digital Input Module

Delta DVP08ST11N adds eight built-in switch inputs to a compatible DVP Slim PLC. It belongs to the DVP Slim digital module family. Operating a front-panel switch from X0 to X7 changes its input bit and indicator LED. It occupies eight CPU input addresses and has zero physical outputs. In a system with other PLC input and output modules, it lets the program read a manual setting.

Power, mounting and addressing

The 24 V DC supply comes from the main unit’s internal expansion bus. Delta’s instruction sheet lists 0.5 W consumption, an operating range of 0–55 °C and a weight of 60 g. The module is 25.2 mm wide and fits a 35 mm DIN rail. With power isolated, connect it to the CPU’s right-side expansion chain and secure the side clips. Each digital input comes from its own switch, so these inputs require no separate field signal wiring or external supply.

X0–X7 are the local panel labels. In Delta’s example, when DVP08ST11N is the first expansion after a DVP12SA11R, the CPU reads its inputs at X20–X27. Local X0 maps to X20. Check the start address when the CPU or preceding modules change. Use the actual CPU X address in the ladder diagram and on the HMI diagnostics screen.

Programming software and cable

Load the application into the host CPU. For compatible DVP-SS2, DVP-SA2, DVP-SX2 or DVP-SV2 CPUs, use WPLSoft or ISPSoft. Set up the ISPSoft connection in COMMGR. For example, the SS2 COM1 RS-232 communication port uses UC-PRG020-12A from PC USB or UC-MS020-01A from a PC RS-232 port.

Delta also lists DVP08ST11N among DVP-SV3/SX3 expansion modules. These CPUs use DIADesigner. Select the programming cable to match the CPU model and port. On SV3/SX3, the connection to the CPU uses a USB data cable or RJ45 Ethernet.

Selector switches and panel applications

Use the built-in switches for cabinet-level recipe selection, training or input-bit testing. For operator controls outside the cabinet, connect a rotary selector switch or pushbutton to a suitable field input. A limit switch, inductive sensor or photoelectric sensor also needs a card that accepts its signal. Match the field input common to the sensor’s sink/source wiring.

When using two built-in switches to select between two recipes, for example, assign 00 to no selection, 01 and 10 to valid selections, and 11 to an invalid combination. Keep the start command separate from the selection in the program. Use safety relays and contactors that suit the machine’s emergency stop and guard circuits. Choose a suitable output card and, where needed, an interposing relay for ordinary coil loads. Lay out the panel components to leave service access and route field wiring to reduce electromagnetic interference.

Related models

DVP08SM11N has eight 24 V DC field inputs and DVP08SM10N has eight AC field inputs. DVP16SM11N is a 16-input choice for larger DC installations. DVP08SN11T is the eight-channel transistor output model. When choosing used digital input modules, check the part number, signal type and CPU family.

Editor’s Note

Check the 08ST11N label and make sure all eight switches are present. Ask for clear photographs of the side connector and its clips.

Move each switch to ON and OFF in turn. Check its LED first and then the corresponding X bit in the online monitor.

If the LED changes while the monitored bit stays fixed, check the module order and actual address before replacing the card.

If all channels disappear together, isolate power and check the side connector and retaining clip. For a single intermittent channel, compare switch travel and the bit in both positions.

The switches stay in their physical positions when power returns. During commissioning, test the startup conditions and invalid selections as well.

PDF manuals and technical documents

See Delta DVP PLC files for series documentation. Page two of the DVP08ST11N instruction sheet covers power, mounting and the X20–X27 addressing example.

Navigation · Delta automation · Delta PLC · DVP PLC series · Expansion modules · DVP08ST11N model page

External references

Delta DVP08ST11N instruction sheet · Delta DVP catalogue