Delta DVP32HM11N

Delta DVP32HM11N — 32-Point Digital Input Expansion Module

Delta DVP32HM11N is a 32-point digital input module with no outputs, introduced for the DVP-EH2 PLC family. It brings pushbutton, limit switch, relay contact and compatible sensor signals into the host CPU. It is not a standalone CPU and does not execute its own PLC program. On this model, the N suffix identifies the absence of outputs.

Power supply and input specifications

The specified supply is 24 V DC, with a 20.4–28.8 V DC operating range and 3.9 W consumption. Check the DC supply polarity and equipment label. Do not wire it as an AC-powered 32HN00R/T unit. No 500 mA auxiliary 24 V output is specified for this model; size the sensor supply against the available power-source capacity.

The 32 inputs accept 24 V DC sink/source signals. The instruction sheet specifies 5 mA input current, an ON level above 16.5 V, an OFF level below 8 V, and approximately 20 ms response time. Photocoupler isolation and channel-status LEDs are provided.

NPN/PNP sensors and dry contacts

NPN/PNP wiring is selected through the S/S common terminal: connect S/S to +24 V for an NPN open-collector sensor, or to 0 V for a PNP sensor. Connect the sensor output to the required X input. A dry contact completes the input circuit to the supply rail opposite the selected common. When replacing an inductive sensor or photoelectric sensor, verify its actual output type and the machine drawing.

With an input response of about 20 ms, this module should not be selected as a high-speed counter interface for encoder pulses. Capturing short pulses depends on input response and CPU scanning. Use documented high-speed CPU inputs or a suitable dedicated module where fast counting is required.

Host compatibility and input addressing

Delta’s product introduction identifies it as a DVP-EH2 32DI module; the same code also appears in the EH3 expansion ordering table. Confirm the exact host CPU, expansion connection and total permitted I/O capacity before replacement. A Slim or E2 module with a similar point count requires its own compatibility check.

X addresses use octal numbering: X7 is followed by X10. As an example, when this is the first digital expansion after an EH CPU with 16 inputs, its 32 inputs normally occupy X20–X57. Earlier digital modules and the CPU’s allocation rules determine the actual starting address. Verify every input in online monitoring during commissioning.

Programming software and connection cable

No separate program is downloaded to DVP32HM11N. Its inputs are used in the host CPU’s PLC programming project. Select a WPLSoft or ISPSoft version supporting that CPU. Read the assigned X contacts in the ladder program. Analog-module FROM/TO and CR configuration templates do not apply to this standard digital input module.

For a host CPU with an 8-pin mini-DIN RS-232 programming port, UC-PRG020-12A is a suitable USB programming-cable option. A serial cable may require an appropriate USB-to-RS-232 converter at the computer. Configure the driver, COM port and the relevant COMMGR connection when using ISPSoft. The computer cable connects to the CPU; the expansion connection joins the CPU and module.

The module has no separately assigned RS-485 station address or Modbus RTU settings. Remote access uses the host CPU’s communication facilities and the project’s data mapping.

Panel installation and commissioning

The specified operating temperature is 0…55°C. Secure the module inside a suitable enclosure and separate input wiring from power cables. Review grounding, appropriate supply fusing and electromagnetic interference measures together. Machine emergency stop and safety relay functions require an appropriate safety design beyond reading a standard PLC input.

Editor’s Note

Start with the complete label: 32HM11N is the DC-powered 32-input model. Do not transfer wiring from a similar-looking 32HN or 32HP unit. Establishing whether the device reads inputs or drives outputs saves considerable diagnostic time.

Inspect the terminals, side expansion connector, cable and rail clip before powering up. Loose or oxidised connections can make several channels appear faulty together. Disconnect power before removing or installing the expansion connection.

Test all 32 inputs separately, checking both the channel LED and the expected X address in the CPU. If the LED behaves correctly but a different address changes, investigate allocation and module order first. Prevent unexpected machine motion throughout testing.

When a group of inputs disappears, check S/S, sensor 0 V returns and the 24 V supply under load before condemning the board. For a single-channel fault, compare the sensor and cable with a known-good input.

For an input stuck ON, separate field leakage voltage and sensor faults from the module before examining its protection and photocoupler circuit. Retest every input after repair. An illuminated LED alone is not a complete functional test.

For second-hand equipment, request clear photographs of the complete label, expansion connection and terminals. Prefer a 32-channel test with a compatible CPU. Distinguish power-supply faults from input faults before deciding on repair or replacement.

PDF documentation

Use our Delta DVP PLC files page for documentation. The legacy English product introduction covers the model’s supply and hardware; it is shared with DVP02LC-SL, whose load-cell specifications do not apply to DVP32HM11N. The DVP-EH DIDO sheet covers input wiring and addressing; the cable guide covers the host CPU’s computer connection.

Related topics and navigation

DVP08HM11N and DVP16HM11N provide 8 and 16 inputs respectively. DVP32HN00R provides 32 relay outputs, while DVP32HP00R provides 16 inputs and 16 relay outputs. Similar point counts do not establish interchangeability.

Delta main page | Delta PLC | DVP PLC series | DVP EH modules | DVP32HM11N | DVP PDF files

External manufacturer documents

Delta DVP32HM11N/DVP02LC-SL product introduction — legacy English manufacturer document | DVP-EH DIDO — 21 February 2024 manufacturer sheet, archive copy | Delta PLC/HMI Cable Selection Guide — English